•60 Models of torpedoes are sometimes tested in a horizontal pipe of flowing water, much as a wind tunnel is used to test model airplanes. Consider a circular pipe of internal diameter 25.0 cm and a torpedo model aligned along the long axis of the pipe. The model has a 5.00 cm diameter and is to be tested with water flowing past it at 2.50 m/s. (a) With what speed must the water flow in the part of the pipe that is unconstricted by the model? (b) What will the pressure difference be between the constricted and unconstricted parts of the pipe?

•60 Models of torpedoes are sometimes tested in a horizontal pipe of flowing water, much as a wind tunnel is used to test model airplanes. Consider a circular pipe of internal diameter 25.0 cm and a torpedo model aligned along the long axis of the pipe. The model has a 5.00 cm diameter and is to be tested with water flowing past it at 2.50 m/s. (a) With what speed must the water flow in the part of the pipe that is unconstricted by the model? (b) What will the pressure difference be between the constricted and unconstricted parts of the pipe?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 1:4 scale torpedo model has been built. The prototype is expected to move at a speed of 6m/s in water at 15°C. What should be the velocity in the model if, a) the test is done in a stream channel at 15°C; and b) the test is done in a wind tunnel at 27°C and a pressure of 20 atm?
A 3500 Ibm car moving at 25 mi/h is accelerated at a constant rate of 15ft/s^2^ up to a speed of 50 mi/h. What are the force and total time required?
8.1. An airplane wing of 3 m chord length moves through still air at 15°C and 101.3 kPa at a speed of 320 km/h. A !:20 scale model of this wing is placed in a wind tunnel, and dynamic similarity between model and prototype is desired. (a) What velocity is necessary in a tunnel where the air has the same pressure and temperature as that in flight? (b) What velocity is necessary in a variable-density wind tunnel where absolute pressure is 1 400 kPa and temperature is 15°C? (c) At what speed must the model move through water (15°C) for dynamic similarity?
P6.2 A 1:80 scale model of an aircraft was tested in air at 20C°moves with speed 40m/s a- What is the speed model if its submerged in water at 26C°, Vair = 14.86 * 10-6 m Vwater = 0.864 * 10-6" m2 [V=2.325 m/s] b- Determine the air resistance to the prototype if model water resistance is 7.43N. [Fp=2.643 N]
Q.4 A 200 mm diameter pipeline is laid on the ground. At a particular point, the piezometric head is 20 m. Total energy head of water at a point is 26 m. The Discharge (L/s) of water through the pipe is Type your answer here.. SUBMIT
A small, axisymmetric, low-speed wind tunnel is built to calibrate hot wires. The diameter of the test section is 6.68 in, and its length is 12.5 in. The air is at 60°F. At a uniform air speed of 5.0 ft/s at the test section inlet, by how much will the centerline air speed accelerate by the end of the test section? What should the engineers do to eliminate this acceleration?
A wind tunnel is used to measure the pressure distribution in the airflow over an airplane model. The air speed in the wind tunnel is low enough that compressible effects are negligible. The Bernoulli equation approximation is valid in such a flow situation everywhere except very close to the body surface or wind tunnel wall surfaces and in the wake region behind the model. Far away from the model, the air flows at speed V∞ and pressure P∞, and the air density ? is approximately constant. Gravitational effects are generally negligible in airflows, so we write the Bernoulli equation asP + 1/2 ρV2 = P∞ + 1/2 ρV2∞ Nondimensionalize the equation, and generate an expression for the pressure coefficient Cp at any point in the flow where the Bernoulli equation is valid. Cp is defined as Cp = P−P∞/1/2ρV2
fluid mechanics
Hi Pls include FBD
Solve it..
A turbine model has the following characteristics: Effective power: 13, 6 kW; Rotor Diameter: 0.38 meters, Flow: 0.34 ms, Energy Jump: 26.5 J / Kg and 3 R.P.S. rotation It is desired to construct a geometrically similar 1.20 meter diameter turbine that provides a power on the 656 kW axis, we ask: to calculate and justify its answers: a) the specific rotation; b) the unit quantities (rotation, flow and power); c) the rotation, flow and power of the model (bi-unit quantities).
The Keystone Pipeline opener photo hasD = 36 in. and an oil flow rate Q = 590,000 barrels per day(1 barrel = 42 U.S. gallons). Its pressure drop per unitlength, ∆p/L , depends on the fluid density ρ , viscosity μ ,diameter D , and flow rate Q . A water-fl ow model test, at20 ° C, uses a 5-cm-diameter pipe and yields ∆ p/L ≈ 4000Pa/m. For dynamic similarity, estimate ∆ p/L of the pipeline.For the oil take ρ = 860 kg/m 3 and μ = 0.005 kg/m . s.