PROBLEMI.2 A HYDRAULIC TURBINE IS REQUIRED TO PRODUCE 800 KW POWER AT 500 RPM UNDER A NET HEAD OF 40 M. FOR INITIAL TESTING A GEOMETRICALLY SIMILAR MODEL OF 1:4 SIZE NEEDS TO BE TESTED IN A LAB WHERE AVAILABLE HEAD IS 10 M.THE OPERATING SPEED AND POWER PRODUCED BY THE MODEL RESPECTIVELY IS

PROBLEMI.2 A HYDRAULIC TURBINE IS REQUIRED TO PRODUCE 800 KW POWER AT 500 RPM UNDER A NET HEAD OF 40 M. FOR INITIAL TESTING A GEOMETRICALLY SIMILAR MODEL OF 1:4 SIZE NEEDS TO BE TESTED IN A LAB WHERE AVAILABLE HEAD IS 10 M.THE OPERATING SPEED AND POWER PRODUCED BY THE MODEL RESPECTIVELY IS

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hydraulic cylinder is to compress a vehicle body in 14.15 seconds,The operation requires a stroke length of 2720 mm and force of 54.45 kN.If a 9 N/cm² hydraulic pump has been selected ,find the following; (a) Required Piston area and its diameter (b) The necessary pump discharge (c) The hydraulic power capacity in horsepower (hp).
Solve it on priority and correctly
fluid mechanics subject! please help ne solve this in details!
An 8 m/s wind enters a wind turbine rotor with a diameter of 36 m. Assume the air density 1.2 kg/m3 Calculate: The power of incoming wind, The maximum power extracted by the wind turbine, If the gearbox, generator and electrical transmission and processing efficiencies are 0.85, 0.96 and 0.95, respectively, what is the turbine effective converted power
Solve it correctly please.I will rate accordingly. Pl
Determine the non dimensional parameters that can be employed for scaling studies in centrifugal pumps.
volume flow rate requirement of 21it/s with an of 60К Pa. A system has a index run ΔΡ Find an appropriate pump from the manufacturer's catalogue gives the following information for a centrifugal pump operating at 24rev/s: kPaQ lit/s 98.76 0.5 95 1 88.76 1.5 80 68.38 2.5 55 38.76 3.5 Two geometrically similar pumps are running at the same speed of 1000r.p.m. One has an impeller di ameter of 0. 4m and discharge of 301/s against a head of 20m. If the other pump gives half of this discharge rate, determine the head, diameter and power of the second pump.
Please Answer all my Question .. Please help me , I don't want plagiarism.
... height Fire hoses used in major structural fires have an inside diameter of 6.40 cm. Suppose such a hose carries a flow of 43 L/s. The hose rises up 13.3 m along a ladder to a nozzle having an inside diameter of 3.00 cm. What is the starting pressure at the fire truck? Use p=1000 kg/m³ and g =9.8 m/s? Answer in KPa. No label, no unit, number only.
Please show how to solve parts a, b, and c shown below. The topic is fluid mechanics. Thank you.
4.11 Verify the design of the San Francisquito power plant, which has the following specifications: P=32,200 hp, H=800 ft., N=171.4 rpm. Estimate the number of jets, if each jet is 14 in. in diameter. Ans: The wheel diameter is 176 in. and the number of buckets is 22. These val- ues are available in the public domain from the plant specifications.
What is the maximum power generated by the wind farm with wind speed of 4 m/s? Typical wind turbines have rotor diameters from 40 m to 90 m (Assume increment of 5 m for this problem)-40 m is 80% efficient and efficiency decreases by 5% for every 5 m increase in diameter (i.e. 45 m=75%, 50=70...)-The ridge is 10 km long and wind turbines will be spaced in a single row. •Power in the wind per unit area of circular area is 1/2ρv3W/m2 (v is the wind speed, ρ is 1.3 kg/m3 for air) •Wind turbines cannot be spaced closer than 5 times its diameter without loosing power also there are no partial turbines.