60 m 390 mm 600 mm Q-2 Q-2: If the 280-kg drum has a center of mass at point G, determine the horizontal and vertical components of force acting at pin A and the reactions on the smooth pads C and D. The grip at B on member DAB resists both horizontal and vertical components of force at the rim of the drum.

Q: 1. T-square is used for drawing: A. horizontal lines b. inclined lines c. vertical lines d. lines at…

A: We have to find term 1,2,3

Q: Problem: Determine F to keep the block at rest. 500 kN IS 30

A: Given: A block of weight 500 kN is resting on a inclined plane, which makes an angle of 300 with…

Q: Find the value of a. TO a. Vs +3

A:

Q: 2. If Tc= (-5) find TF. TK and TR.

A: Given:  TC=-5

Q: Find reaction at A.

A:

Q: What will be the value of F,? 10 kN 5 kN + F1 F2

A: Resolve the other 3 components in terms of force F1. The 10 kN along the F1 is = (10 x cos90) = 0…

Q: 04C) Cable reaction force is the cable and acts .. . the object. a. perpendicular to, away from O b.…

A:

Q: In determining the net cross sectional area of a structural steel tension member, the diameter of a…

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: The coal consumption per hour is the ratio of heat of combustion and calorific value.

A: True

Q: A stone is thrown vertically upward from the ground with a velocity of 300ft/s. How long must one…

A:

Q: 3. if you had to lift a truck and had a pole, a rope and a fulcrum, you could do it! A kid could do…

A: for third kind of lever fulcrum lies at one end and object other...

Q: NOTE: Equal grades for each question will have (20 Marks) Q1: Find a unite vector perpendicular to…

A: A vector is an amount that has both extent, as well as course. A vector that has a size of 1 is a…

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: Solve 0.782bar in p/q form

A: Given that : x = 0.782782782....... We need to find it in the form of p/q

Q: Early showerheads consumed either 5 or 7 gallons of water per minute (gpm). Federal plumbing…

A:

Q: If a force doubled, impulse will triple. True or false

A:

Q: The point of contraflexure is a point where a. Shear force changes sign b. Shear force is maximum c.…

A: A point of contra flexure is a point in the bending moment diagram where the bending moment is zero…

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN 1.2…

A:

Q: 07A) Beam carry .. .. loads and therefore the line of action of the forces will be .. the beam axis.…

A: Option d is correct.

Q: 1 4 ind the degree of freedom (F) of the mechanism in the figure.

A: Degree of freedom is defined as a number of input required in a mechanism to get the constrained…

Q: 6.A 1.5-m pendulum swing through an angle of 6º.How wide is the swing, to the nearest centimeter?

A: To find: The value of width of the swing. Given: The value of length of the pendulum is, l=1.5 m.…

Q: For the laser cutting of the shown path, determine the absolute and incremental coordinates of the…

A: given; findabsolute and incremental co-ordinate;

Q: The magnitude of a vector: a.Can be positive or negative. b.Must always be negative. c. Must…

A: The magnitude of a vector: Answer: c. Must always be positive.

Q: digiodens Ild bravou liedsand Thevein Ils dezod 6. A stone is thrown with a velocity of 15 m/s and…

A:

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: to move a force of 1713 lbs using a 100 psi what size bore in diameter would it need in inches

A: Given data: F=1713 lbsσ=100 psi Need to determine the size bore in diameter.

Q: olve show full solution

A: To find:The principle stress at point A and absolute maximum normal stress at and absolute maximum…

Q: The steel rod shown below is 2inches in diameter and is subjected to an eccentric 2000 lb load…

A: Given Data: The eccentric load is P = 2000 lb. The eccentricity is e = 1". The diameter of the…

Q: .a. 12 b.. 3. C. 12 12.(2.6+1.5)-1.1? a.4.1 Perform as indicated: Write the letter of your choice on…

A: Hi and thanks for the questions. Since you have asked multiple questions, we will solve the first…

Q: Two forces are acting at an angle of 180°. The bigger force is 80N and the resultant is 40N and…

A:

Q: 1. If a sheet of aluminum weighs 90 lb, a similar-sized sheet of magnesium would weigh O A. 30 lb. O…

A:

Q: Complete the each drawing by adding the missing details in 5 and 6 both questions.

A:

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Q: If a turbulent water flows inside the piping system, the vertical distance h=30 mm, what is the…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.