6.2 THE FOLLOWING PROVISIONS IN A CONSTRUCTION CONTRACT ARE UNENFORCEABLE: CHECK ALL CORRECT STATEMENTS PROPERLY CONNECT VALVES REMOVE ALL CONTAMINATED WATER MACHINE PARTS TO A TOLERANCE OF 0.0008 IN. + 0.0002 IN. CLEAN ALL PARTS BEFORE BEFORE WELDING

Q: 3. Discuss the major techniques followed in highway for controlling emission.

A: Various techniques that is used to control vehicular emissions:

Q: Hand/Power Tool Demonstration and Procedure for safety  Demonstrate the ability to identify hazards…

A: Inability to identify or acknowledge hazards that are present or could have been expected is one of…

Q: A 127mm x 127mm x 12mm angle bar is connected to a gusset plate with 25mm diameter bolt as shown in…

A:

Q: A beam with a span of 4.5 metres carries a point load of 30 KN at 3 metres from the left support. If…

A: Given data- Span of the beam L=4.5 m, Point load = 30 kN at 3 m from the left support, Section…

Q: Situation 4: A uniform 80-m pipe that weighs 960 kN is supported entirely by a cable AB of…

A:

Q: Problem I. For the beam shown, a) Compute for the reaction at all supports b) Draw the shear and…

A:

Q: 3. A horizontal circular plate weighing 100N is suspended as shown from three wires that are…

A:

Q: Provide an illustration of universal testing machine with parts and provide brief descriptions for…

A: Question is based on the universal testing machine (U.T.M) . U.T.M is a machine used to determine…

Q: Tension only members B 4m 5m 5m 20kN C 5m D

A: A truss is given as shown in the figure above and it has been asked in the question to determine the…

Q: Problem # 4: Three links are used to support load P 10.25 kips. Disregarding any deformation for…

A:

Q: THE FOUR RIGID GEARS, LOADED AS SHOWN IN THE FIGURE ARE ATTACHED TO A STEEL 2-IN.-DIAMETER SHAFT.…

A:

Q: The mass of body A is 45 kg. The coefficient of friction for bodies A, B, and the ramp C is 0.10.…

A:

Q: 2. A grad of 1.5% intersects a grade of -2.5% at station 1+080 of elevation 68.94m. If the summit is…

A: Solution-The given values are as follows  The grade g1=1.5%The grade g2=-2.5%Station…

Q: A repair truck carries 121 feet of 3⁄4-inch copper tubing, 43 feet of 1⁄8-inchcopper tubing, 76 feet…

A: Given :  3⁄4-inch copper tubing = 121 feet 1⁄8-inch copper tubing = 43 feet 1-inch conduit pipe =…

Q: A homogeneous triangular plate of weight W has wheels at B and C. The wheels are of negligible…

A:

Q: FIGURE SHOWS A STEEL SHAFT OF LENGTH L = 1.5 M AND DIAMETER D = 25 MM THAT CARRIES A DISTRIBUTED…

A: For the given shaft,

Q: Select from the following, the type of admixture that you will use if: The work will be carried out…

A: Type B admixture is to be used at the specified Location of Jericho as the temperature in that place…

Q: Situation 7: Using the figure below, -m 1 m- e B 1014 m E 1.5 m 1.5 m 1.5 m 1. If P = 3,000 N and Q…

A: A truss is given as shown in the figure above and it has been asked in the question to determine the…

Q: a) The length of course DE, in meters, is b) The bearing of course BC is c) The perimeter of the…

A: For the given data, the latitude and departure are found out below after converting the given…

Q: For the tension member shown, determine the total service load (DL + LL) if LL = 4DL. Use A36 steel…

A:

Q: name three requirements contained in the specifications regarding material

A: A specification often refers to a set of document requirements to be satisfied by a material or…

Q: irplane on the amusement park ride moves along a path de e equations r= 4 m, 0 = (0.2t) rad, and z =…

A: To find the velocity (vz)-

Q: A boat is towed at the rate of 12mi/hr. At t=0, the towing line is cast offand a man in the boat…

A: A boat is being towed at the rate of 12 mi/hr. At the instant (t = 0) that the towing line is cast…

Q: K U U AB GH HI JO DL B Select all 14 zero-force members to receive full credit. EF H ✔AG ✔ CH ✔NI C…

A: Given a truss with various members  Required = identification of Zero Force members It will be…

Q: Situation 8: A couple acting on the winch at G slowly raises the load W by means of a rope that runs…

A:

Q: Accuracy and Precision for all the following can not determine the accuracy of measurments can not…

A:

Q: adamson.blackboard.com 20 minutes remaining Question 1

A:

Q: 1) The beam is loaded as shown in the figure. Derive the shear and bending moment equations and draw…

A: Find  Shear and bending moment equation and draw SFD and BMD  Point C is pin joint, it mean's moment…

Q: Determine the time needed to pull the cord at B down 4 ft starting from rest when a force of 10 lb…

A:

Q: For the figure shown in figure F-34, identify the reaction components, the tension at the ends, and…

A:

Q: Situation 4: The uniform 50 kg plank in the figure is resting on rough surfaces A and B. The…

A: Free body diagram: 50 kg = 50 x 9.81 = 490.5 N 80 kg = 80 x 9.81 = 754.8 N

Q: List uses of a tirfor machines

A: A Tirfor machine, also known as a wire rope winch or a hand-operated hoist, is a versatile tool used…

Q: Situation 11: A transmission tower is subjected to the wind loads shown. 5 KN 7 kN 3 kN THEE pem 1.5…

A:

Professional survey

A professional survey is a systematic questionnaire that the target audience fills out online, usually by filling out google forms. Professional surveys can vary in length and format. The data is stored on a website and the testing tool usually provides a certain level of data analysis in addition to a professional expert review. Several professional online survey softwares are present worldwide like, SoGoSurvey, SurveyGizmo, SurveyMonkey, Qualtrics, and so on.