6.14 Determine the nodal displacements and the element stresses, including prin- cipal stresses, due to the loads shown for the thin plates in Figure P6-14. Use E = 105 GPa, v=0.30, and r = 5 mm. Assume plane stress conditions apply. The recommended discretized plates are shown in the figures. Use a computer program to solve these. 400 mm XI 400 mm 30 kN Figure P6-14 (c)

6.14 Determine the nodal displacements and the element stresses, including prin- cipal stresses, due to the loads shown for the thin plates in Figure P6-14. Use E = 105 GPa, v=0.30, and r = 5 mm. Assume plane stress conditions apply. The recommended discretized plates are shown in the figures. Use a computer program to solve these. 400 mm XI 400 mm 30 kN Figure P6-14 (c)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please do not copy posted solutions as they are not right. Please show detail. Please do 9-29. The final answer is supposed to be 18.0 kN. Do not answer if you do not know how to get 18.0 kN.
3-10 A rigid bar rests on aluminum-alloy and steel uprights, as shown in the figure.( a) Determine the inclination of the horizontal bar after a raise in temperature of 100°C. Assume the coefficients of thermal expansion for aluminum alloy and Steel to be, respectively, 23.2 X 106/°C and 11.7x 10°/°C. To a greatly exaggerated scale, sketch the position of the bar after the raise in temperature. (b) What stresses would develop in the upright members if their tops were prevented from expanding? Let the elastic moduli for aluminum alloy and steel be, respectively, 75 GPA and 200GPa. Compare the obtained stresses with those given in Table 1 of Appendix. (Hint: The tendency for thermal expansion is counteracted by elastic contraction.)
For the previous problem, compute the following six stress quantities: Ox, Oy, 0z, Txy, Tyz, Tzx. Assume this is an aluminum alloy (E = 10,000 ksi, G = 3800 ksi, v = 0.33). Do not forget units!
A rectangular column (blue color) is fixed to a rigid ground (brown color). As shown in the figure, the column is under two external loadings at C. Determine the state of stress at point K of the column and represent the stress components on a stress element.
In the figure below, A 50 mm shaft is subjected to a reversed load P = 2700 N. Find the length (L), if the stress at the fillet equal to the stress at the center. 6.25mm 2700N 2700N 62.5 s0 375 Fillet Center Fillet All Dimensions in mm
A pushrod in the valve mechanism of an automotive engine has a nominal length of 203 mm. If the rod is made of SAE 4140 steel, compute the elongation due to a temperature change from -20°C to 140°C. TABLE3-4 Cocfficients of thermal expansion. a. for some
How would you solve this
Just Solve a Use Abaqus
There’s a force acting in the Y and Z direction
Q1/ (A) - The mechanism of femur bone is approximated as a circular tube (3 cm and 2 cm are the outer and inner diameter respectively) under loads as shown in figure Q1-A, determine the state of stresses at the points A and B. 40 cm 5 cm 380 N Figure Q1-A 300 N
Two forces, 100 kN and 200 kN, act on the rectangular column in the figure. Find the stresses at A and B points according to the given and show them on the stress element.
Refer to the figure. The steel rod is supported by an aluminum plate of 8 mm thickness. Force P pulls down the rod through the 12 mm hole in the aluminum plate. Neglect all weights of the rod and plate, and based on the design criteria that the maximum allowable shear stress in steel to be 18 MPa, calculate the allowable value of P in kN. Round to the nearest tenth. 10 mm T 12 mm- 40 mm- P 8 mm