6.11. In the two-bus system shown in Figure 6.24, bus 1 is a slack bus with V₁ = 1.040° pu. A load of 100 MW and 50 Mvar is taken from bus 2. The line impedance is z12 = 0.12 + j0.16 pu on a base of 100 MVA. Using Newton- Raphson method, obtain the voltage magnitude and phase angle of bus 2. Start with an initial estimate of |V₂|(0) = 1.0 pu and 82 (0) = 0°. Perform two iterations. 2 100 MW 212 = 0 12 + j0.16 --- 50 Mvar 어 FICURE 621 V₁ = 1.040°

6.11. In the two-bus system shown in Figure 6.24, bus 1 is a slack bus with V₁ = 1.040° pu. A load of 100 MW and 50 Mvar is taken from bus 2. The line impedance is z12 = 0.12 + j0.16 pu on a base of 100 MVA. Using Newton- Raphson method, obtain the voltage magnitude and phase angle of bus 2. Start with an initial estimate of |V₂|(0) = 1.0 pu and 82 (0) = 0°. Perform two iterations. 2 100 MW 212 = 0 12 + j0.16 --- 50 Mvar 어 FICURE 621 V₁ = 1.040°

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A network consisting of a set of generator and load buses is to be modeled with a DC power flow, for the sake of conducting a contingency analysis. The initial flows calculated with the DC power flow give the following information: f°2-4 = - 65.3 MW and fº4-5 = 13.6 MW. The following values of LODF and PTDF factors are given: PTDF54,2-4 = -0.2609, LODF2-4,4-5 = -0.6087. Calculate the contingency flow on line 2-4 due to outage of line 4-5. Select one: O a. -75.5MW O b. None of these O c. -68.85MW O d. -73.58MW O e. 75.5MW O f. -61.75MW
12. Revi i. What difference you noticed in voltage regulation between RL and RC Loads? Why? i. Maximum voltage regulation occurs when power factor is In the case of inductive loads, for a fixed value of VR and I, the voltage regulation of the line increases with the ii. in power factor. iv, What are main reasons for voltage drop in transmission line?
5/The phase angle between magnetizing component current and core loss component current is 180o Select one: True False
pls explain by computer line . in less than 30 min.
In terms of cable performance, what are the effects of temperature fluctuations on transmission cabling?
Power system
A power system consists of 400 buses out of which 30 buses are generator bus. 40 buses are the ones with reactive power support and 15 buses are the ones with fixed shunt capacitors. All other remaining buses are load buses. It is proposed to perform a load flow analysis in the system, using Newton-Raphson method, then size of Jacobian matrix is
Why are resistors and inductors considered to be series impedance and capacitors considered as shunt impedance in transmission line modeling?
To qualify system stability, we use: a. Routh criterion b. Phase margin c. Gain and phase margin d. Gain margin
Q4 (a) (b) A 4-bus power system, as shown in Figure Q4a, of which the parameters are given in Table Q4a; the p.u. value of every component is given based on its own base values (rating). i) Draw an impedance diagram of the network, showing all impedances in p.u., on 1000 MVA and 20 kV base values in the Generator G3 zone. A three-phase short circuit occurs at busbar 3 through a rearance of j0.12 p.u., where the pre-fault voltage is 525 kV and the pre-fault current is neglected. Calculate the short circuit current in p.u. using Thevenin's Theorem. Describe the data required for each component of a typical power network when analysing faults, and the reasons for needing each item of data. T, bus 1 ∞to ΔΥ G₁ G₂ G3 T₁ T₂ Тз Transmission line: 150 Ω bus 4 T₂ bus 2 150 Ω 150 Ω G₂ YE bus 3 T₂ 머( YEA Figure 04a 500 MVA, 13.8 kV, XG1= 0.20 p.u. 750 MVA, 18 kV, XG2 = 0.18 p.u. 1000 MVA, 20 kV, XG3 = 0.17 p.u. 500MVA, 13.8 (A) /500 kV, XT1 = 0.12 p.u. 750 MVA, 18 (A) /500 kV, XT2 = 0.10 p.u. 1000…
Problem 6 The zero-, positive-, and negative-sequence bus impedance matrices for a three-bus three-phase power system are: [0.10 Zbus 0 = j 0.20 per unit 0.10 [0.12 0.08 0.04 Zbus 1 = Z bus 2 = j|0.08 0.12 0.06 0.04 0.06 0.08 The prefault voltage is 1.0 Determine the per-unit fault current and per-unit voltage at bus 2 for: per unit. a) A bolted three phase fault at bus 1 b) A bolted single line-to-ground fault at bus 1. c) A bolted line-to-line fault at bus 1. d) A bolted double line-to-ground fault at bus 1.
In the Transmission Line Simulator, the Transmission Line is composed of which parameter/s? O A. The Shunt Conductance Only O B. The Series Impedance and Shunt Capacitance O C. The Shunt Capacitance Only O D. The Series Impedance Only