i need graph values of given points and slope graph on graph paperThe dot spacing given for figure 1 will be used as 3.4. There are 6 points in total. The distance between them is 3.4. Figure 1. The data points of a disc on air tableTable 1. X-t datat (s)X (ст) 6. The points given in the Figure 1 are obtained by the motion of a disc on an air table. FillTable 1 and sketch the related graph in order to calculate the velocity of the disc. Thefrequency of the spark timer is f= 20 Hz

Six continues dots with equal spacing of distance, d = 3.4 cm Frequency of spark timer is given as,…

Answered: 6. The points given in the Figure 1 are…

Similar questions

Review: Trigonometric Ratios in a Right Triangle 2 Please answer the following question(s): 1. Calculate a: 8 cm a = a Note: the angle should be in degrees. If you use inverse trigonometric functions in the Mathtype tool the angle returned is in radians. 5 cm 0 SENSE MAKING What are the maximum and minimum values a can have? Do your calculations support that?
Whats the main difference between distance and displacements. Choose all that apply. 1. distance is a vector and displacement is a scalar 2. distance is how far and displacement is how far in which direction 3. Displacement is defined by magnitude and direction both but distance is defined by magnitude only 4. displacement is calculated by how far the object travels without paying attention to the direction of travel, and distance is calculated by the change in position it the object 5.displacement is calculated by Calcutating the change in position of the object and distance is calculated by how far the object traveled without paying attention to the direction of travel. 6. displacement is a vector and distance is a scalar.
. which of the following statements regarding a positive relative projection height is true? a. the time to the peak heaight will be greater than the time down from the peak height b. the projection angle will be the same as the angle upon landing c. the tme to the peak height will be less than the time down form the peak height d. none of the other staments are true. e. the time to the peak height will be equal to the time down form the peak height
How do you solve for Resultant given this information. I was able to do the graphical method but I am unsure how n how to use the component method.
Need help as to whether the significant figure numbers are correct or not. Please indicate which ones are not correct and how to correct them.
Show your step by step solutions. 6. With a wooden ruler, you measure the length of a rectangular piece of sheet metal to be 16 mm. With micrometer calipers, you measure the width of the rectangle to be 5.98 mm. Consider 4 significant figures only. Determine: (a) the area of the rectangle; (b) the ratio of the rectangle's width to its length; (c) the perimeter of the rectangle;
HELP FILLING IN BLANKS IN THE PROCEDURE. Procedure 4: Adding Vectors Graphically If you use a ruler and a protractor to draw a series of vectors to scale, the resultant will run from the beginning of the first vector to the end of the last vector. In the picture below, measure the lengths and angles of vectors A, B and C and record these in the 2nd and 3rd columns on the datasheet. Remember to measure angles CCW from the positive x axis. Using cos and sin, calculate the x and y components of vectors A, B and C and record these in the last two columns on the datasheet. Add the x components in the next-to-last column and the y-components in the last column Use Pythagorean Theorem and ArcTan to calculate the magnitude and direction of R Measure the length and angle of vector R Confirm that these two measurements of R match "Fixing the angle" After you do the "four step method" to add vectors, you sometimes have to "fix the angle". Remember that we always start…
Please see attached, thank you

6. The points given in the Figure 1 are obtained by the motion of a disc on an air table. Fill Table 1 and sketch the related graph in order to calculate the velocity of the disc. The frequency of the spark timer is f= 20 Hz