**Problem Statement:**6. The pipe assembly is subjected to an 80-N force. Determine the moment of this force about segment AB of the pipe. Determine the moment about point A, and the orientation of the axis of rotation.**Diagram Explanation:**The diagram illustrates a pipe assembly with several segments in space. The axes are labeled \(x\), \(y\), and \(z\). The pipe segments proceed through several directional changes:- Segment \(AB\): Runs horizontally 400 mm in the positive \(y\)-direction.- Segment \(BC\): Runs vertically downward 300 mm from point B, then turns 90 degrees.- Segment from a point down: Extends downwards and to the left.Key Measurements:- Horizontal Segment (AB): 400 mm- Vertical Segment (BC): 300 mm- Downward Segment: Extends at an angle with 250 mm horizontal and 200 mm vertical measurements. There are two angles shown:- 40° from the horizontal plane.- 30° below the unknown angled line.The 80-N force \(F\) is applied downward at the angle indicated by the two angles presented. An arrow is used to show the direction of the force applied at point C.**Objective:**1. Calculate the moment of the 80-N force about segment AB of the pipe.2. Calculate the moment about point A.3. Determine the orientation of the axis of rotation.

The pipe assembly is subjected to a force of 80 N.F = 80 N

6. The pipe assembly is subjected to the 80-N force. Determine the moment of this force about segment AB of the pipe. Determine the moment about point A, and the orientation of the axis of rotation. 200 mm 30° F = 80 N A 40° 250 mm 400 mm 300 mm 200 mm y A sealen quicon JC

6. The pipe assembly is subjected to the 80-N force. Determine the moment of this force about segment AB of the pipe. Determine the moment about point A, and the orientation of the axis of rotation. 200 mm 30° F = 80 N A 40° 250 mm 400 mm 300 mm 200 mm y A sealen quicon JC

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A thin and weightless beam is supported by a pin connection at 4 and by a roller at B (see figure…

Q: etermine resultant internal forces normal shear and moment at points F and G

A: A structure is loaded with a point load at F at the extreme end of DEF bar.The bar DEF is supported…

Q: 750 N A -500 mm 400 mm 150 mm 450 N C 250 mm B D 600 mm

Q: A rigid bar AB, pinned at end A, is supported by a wire CD and loaded by a force P at end B as shown…

A: Given: E =210 GPa Displacement at B not more than 6mm Diameter of wire = 5mm To Find: Maximum…

Q: Question The electric motor exerts 600 Nm torque on the aluminum shaft ABCD when it is rotating at a…

A: T = 600 Nm GBC = 16 GPa or 16000 MPa GCD = 12 GPa or 12000 MPa dBC = 30 mm

Q: 530 N 310 285 310 mm mm mm 325 mm 550 mm 325 mm

A: Consider the given figure. The vertical reaction at point B is By. The horizontal reaction at point…

Q: 5- Replace the given forces by an equivalent resultant force and a couple moment at point P. [In…

Q: P6.28 A hollow aluminum

Q: The 8.5-kg uniform rod is pinned at end A. If it is also subjected to a couple moment of 50 Nm. The…

Q: Q2. Replace the loading acting on the beam with a single resultant force. Determine (a) the force…

A: Replace the loading acting on the beam with a single resultant force. Determine (a) the force…

Q: Question 1) Determine the x and z components of reaction at the journal bearing A and the tension in…

A: F1 = -800 k F2 = 350 j

Q: Q5 Draw the influence line for (a) the moment at B, (b) the shear at C, and (c) the vertical…

A: A beam with vertical roller support at A such that it resists only moment and horizontal force and a…

Q: ying two points loads L

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

**Problem Statement:**

6. The pipe assembly is subjected to an 80-N force. Determine the moment of this force about segment AB of the pipe. Determine the moment about point A, and the orientation of the axis of rotation.

**Diagram Explanation:**

The diagram illustrates a pipe assembly with several segments in space. The axes are labeled \(x\), \(y\), and \(z\). The pipe segments proceed through several directional changes:

- Segment \(AB\): Runs horizontally 400 mm in the positive \(y\)-direction.
- Segment \(BC\): Runs vertically downward 300 mm from point B, then turns 90 degrees.
- Segment from a point down: Extends downwards and to the left.

Key Measurements:
- Horizontal Segment (AB): 400 mm
- Vertical Segment (BC): 300 mm
- Downward Segment: Extends at an angle with 250 mm horizontal and 200 mm vertical measurements.

There are two angles shown:
- 40° from the horizontal plane.
- 30° below the unknown angled line.

The 80-N force \(F\) is applied downward at the angle indicated by the two angles presented. An arrow is used to show the direction of the force applied at point C.

**Objective:**

1. Calculate the moment of the 80-N force about segment AB of the pipe.
2. Calculate the moment about point A.
3. Determine the orientation of the axis of rotation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:

VIEW

Step 2: Calculation:

VIEW

Step 3: Calculation of moment:

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

5- Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the wrench and the point P(x, y) where its line of action intersects the plate. F, = |-300k) N %3D Fe= [200j| N 2m 500N 30 F = (4001) N
1-42 The 50-lb lamp is supported by three steel rods con- nected by a ring at A. Determine which rod is subjected to the greater average normal stress and compute its value. Take 0 30°. The diameter of each rod is given in the fig- ure. 1-43 Solve Prob. 1-42 for 0= 45°. *1-44 The 50-lb lamp is supported by three steel rods con- nected by a ring at A. Determine the angle of orientation @ of AC such that the average normal stress in rod AC is twice the average normal stress in rod AD. What is the magnitude of stress in each rod? The diameter of each rod is given in the figure. D 0.3 in. 45% B 0.35 in. 0.25 in.
6- Replace the two wrenches and the force acting on the pipe assembly, by an equivalent resultant force and couple moment acting at point O. Force F2 and moment M, are applied at point B. 100 N m =M1 300 N =F1 A В 1000N =F3 -0.5 m-/- 0.6 m- -0.8 m 45° 200 N =F2 180 N · m =M2
Please help me, the previous answer is wrong. ASAP. Thank you, I will like your answer if it is correct.
The solid 34 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. For the loading shown, determine: (a) the shaft deflection at pulley B. (b) the shaft deflection at pulley C. Assume P = 810 N, Q = 480 N, LAB = 260 mm, LBC = 400 mm
The device shown is a part of an automobile seat- back-release mechanism. The part is subjected to the 4-N force exerted at A and a 300-N•mm restor- ing moment exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force. y F =4 N 10 mm 15° 40 mm 300 N-mm
1. The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at A and B. a. Draw the free-body diagram of the beam. b. What are the magnitudes of the reactions at A and B? G 45% A 14" F -1.2 m 1.5 mlm- B 30°