6. Recently a small dinosaur was found fossilized in a "puke sac" because the small dinosaur died when impacted with a Brachiosaurus vomit shower. Toneroso

Q: Hammer arm length = 100 cm Q3/ the accompanying table contain data abtained during a tensile test…

A:

Q: A bending test is done on a specimen with the dimensions, Support span "L" is equal to 21 cm, the…

A: The expression for the stress is Substitute values in the above expression

Q: Strain of Silly Putty: Initial length (L0): 2.85 cm Final length (L): 8.50 cm Strain: % (show…

A: Initial length (): 2.85 cmFinal length (L): 8.50 cm

Q: please refer the attached

A: Since you have asked a question with multiple sub parts we will solve three sub parts for you if you…

Q: What are the elastic modulus (E) and the Poisson's ratio () used to indicate? 2. Illustrate the…

A: The elastic modulus (E) and Poisson's ratio are two important parameters used to describe the…

Q: A 2m long rod is subjected to a tensile force, it's length reduces to 1.5m. What is the magnitude of…

A: Given data  The initial length of the rod= 2m The final length of the rod= 1.5m As we know…

Q: 5kN 2kN-m 1kN/m 1.2- 1.2 t1.2 -2Am B

A: It is required to determine reaction force at support A and B

Q: =o7 Cm) findSmax. tor Figure 0,7 Cm) fin mox. tor tigure tigure. 225 mm J0omm

A: Given Data The force acting in the downward direction is: F=400 N The height of the weld is: h=0.7…

Q: The stress-strain diagram for a metal alloy having an original diameter of 12 mm and a gauge length…

A: Write the given data with suitable variables.

Q: A) An engineer works for a company that has many gray cast iron rods of different diameters and…

A: Given :Load P = 10 kip Material : grey cast iron

Q: Q1: Find a relation between true strain () and reduction in area (r)?

A:

Q: Please show all work!

A: In the problem statement:Given:A stress matrix (ksi) σ:To be found:Calculate the principal…

Q: figure five shows the tensile strength. The graph depicting stress (MPa) vs. stain ( percent ). The…

A: A stress strain diagram, also known as a stress strain curve, is a diagram that depicts the…

Q: please make an ilustration relating pressure to area and force, it can be an example drawing

A: To make: An illustration relating pressure to area and force. Explanation: Consider an image below:…

Q: Would the time not be equal to 1500sec ?  25minutes x 60 = 1500sec

A: Given data Output = 500j/kg T1= 10°C T2= 40°C Density = 1.225kg/m^3 C= 1010j/kg°C Time = 25 min Find…

Q: Given data : Work done=3600 J Displacement=2.1 m Determine Force applied

A: Work done = Applied Force X Displacement

Q: The state of stress at a point in a structure is depicted in Fig. 1. Calculate the normal stress and…

A: Given Data:   To Find: (a) The normal stress σ. (b) The angle θ.

Q: 15° 700 N F. X

A:

Q: Q6: The following stress-strain curve is for a copper alloy (Figure 1 and Figure 2). At fracture,…

A:

Q: Q3: What is the magnitude of true strain (e) if the true stress (o) is 15% larger than engineering…

A: Given data:- True stress=1.15×Engineering stress To find:- Magnitude of true strain

Q: sce M13.5 Strain measurement with rosettes Ea 500 µE Eb -200 με %3D Ec 250 με 30° 30° I| ||

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Problem 1 Figure below shows the stress-strain curve of some specimens in different conditions.…

A: The stress-strain curve is a graphical representation of the data points, where the mechanical…

Q: . For the following diagram, calculate the force needed to is A-36 steel, wire diameter is 0.125…

A:

Q: (2) luhai The difference between shear strain and linear strain

A:

Q: a) Using the expressions for the linear strain tensor, compute the value of the shear strain €12- b)…

A: To find the shear strain from the linear strain tensor, engineering shear strain and  average shear…

Q: The following figure demonstrates the pressure acquired form a direct extrusion process versus the…

A: Given: Extrusion process

Q: 2. A wire is stretched between 2 rigid posts separated by a distance L. If the surrounding…

A:

Q: Given the following stress-strain graph: a. is the modulus of elasticity of "A-514" greater, less or…

A: (a): the modulus of elasticity of A-514 is same asA-572 because the slope of initial stress strain…

Q: You need the shear modulus for a particular material in order to calculate shear strain for a known…

A:

Q: • Part A If e= 27° and F = 5 kN, determine the magnitude of the resultant force acting on the plate.…

A:

Q: 10.19. An electrical-resistance strain gage records a strain of 400 µm/m on a steel tension member.…

A:

Q: In 30 force, if e is the angle between the positive xaxis and the piane contalining the force F, and…

A: Consider the diagram shown below for the force F.

Q: 8. For the following diagram, calculate the force needed to stretch the wire AB by 5%. Wire is A-36…

A: For the following diagram, calculate the force needed to stretch the wire AB by 5%. Wire is A-36…

Q: Q5) material given the data from a tension test ? How would you determine the strain- hardening…

A:

Q: Given, HRB = 4X Find BHN. Given, HRC = 3X %3D Find BHN.

A: Hardness : it is the property of the any material that tell the resistance ability to abrasion or…

Q: A 7075-T6 aluminum tube is 35 ft. long. If you heat it from 65°F to 172°F, how much will its length…

A: Given: Length of the aluminum tube: →L=35 ft Initial temperature→T1=65°F Final temperature→T2=172°F…

Q: Define the term nominal dimensions?

A: In manufacturing, a nominal size or trade size is a size "in name only" used for identification.

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.