6. Find the characteristic impedance expression in terms of the inductance and capacitance parameters. a) Zo=√LC b) Zo=LC c) Zo=√L/C d) Zo=L/C

Q: A three-phase, three-wire CBA system, with an effective line voltage 106.1 V, has a balanced…

A:

Q: Questions 16 to 20 (Write True or False) A16 A larger inductor produces a smaller rate of change of…

A: As per the guidelines of Bartleby we supposed to answer first three subparts of the question for…

Q: At 0-, no currrent flows through the capacitors because they are open, how did you combine the…

A:

Q: 2n -j4n HE Zeg jion -jsn

A:

Q: Determine the capacitance and voltages

A:

Q: What is the value of capacitance if the capacitive reactance is 50 Q .Assume frequency of supply as…

A: In this question we will find capacitance..

Q: Determine the capacitance and voltages (Vrms) across the resistor and capacitor and prove that the…

A:

Q: 1. When a 10 inductor and a 10 capacitor are connected in series, the impedance will be equal to: a.…

A: Given, Reactance of inductor (XL) = 10 ohm Reactance of capacitor (XC) =10 ohm

Q: Two lossy capacitors with Equal capacitance values and power factors of 0.01 and 0.02 are in…

A: Given two lossy capacitors with Equal capacitance values and power factors of 0.01 and 0.02 are in…

Q: Write a report to compare between Ac Through capacitance and AC through in inductance then: For the…

A:

Q: Find the magnitude of the total current.

A:

Q: In alternating current, AC, theory, the voltage through an inductor leads the current by a phase…

A: introduction for series for parallel

Q: Compute the capacitance of (i) parallel plates with plate width w- 2.0 (m), length 1 unit and…

A: Width of plate w = 2 m. Length is given L =1 m. Separation between plates d = 4.6 m. Relative…

Q: Write the relationship between the phasor voltage and phasor current for an inductance. Repeat for…

A: The relationship between the phasor voltage and phasor current for an inductance is given as, By ohm…

Q: find Ztot in rectangular form B) find Ztot in polar form C) find V1 or VL in polar for. ( use…

A: Given: The given circuit is as follows, Formula Used: Ztotal =R+j(XL-Xc)

Q: What impedance vector (0- j15) Ohms represents: A. A pure resistance.         C. A pure capacitance.…

A: Since real part is 0, so it can't be resistor. So option A is wrong.

Q: A capacitor C is connected in series with a 400 resistor across a supply of frequency 60 Hz. A…

A: Impedance Z = 500 ohm Frequency f =60Hz Resistance R= 400 ohm Current flow I = 3A

Q: An electrical circuit with a sinusoidal voltage source, a resistor, and a capacitor all connected in…

A: When the same current flows through all the elements, they are said to be in series. When the same…

Q: In alternating current, AC, theory, the voltage through an inductor leads the current by a phase…

A:

Q: If the phasor current is 45 degrees ahead of the phasor voltage, write down all the possibilities…

A: A good question based on simple current and voltage phasor . Have a look at the solutiom I have…

Q: (a) Determine the impedance Z for maximum average power transfer and the value of the maximum…

A:

Q: A voltage y(t) = 10 cos(2000xt) is applied to a 100-mH inductance. Find the complex impedance of the…

A:

Q: 1. What impedance vector 0 – j22 represents: A. A pure resistance. B. A pure inductance. C. A pure…

A:

Q: draw the thevenin equilvalent circuit and determine the load impedance for maximum power transfer.…

A:

Q: 1. Enumerate five formulas for series-parallel capacitances across Vt source and draw the circuit.…

A:

Q: What impedance vector - j25 represents: A. A pure resistance.            C. A pure capacitance. B. A…

A:

Q: For the given circuit below:  a) Total Resistance,total Inductance,total capacitance and the total…

A: In this question, we need to determine the unknown parameters as mentioned in circuit. Given source…

Q: A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a…

A:

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.