6. Determine the shear force (V) and bending moment (M) at X6.1) X = 3.5 m and 4.5 m7.5 kN/m2m15 kNLLOK10 kN-m9 kN/m3Im Im 1.5 m

Answered: Image /qna-images/answer/04e6530c-2574-4341-afb3-4aaa89cd9cff.jpg

Answered: 6. Determine the shear force (V) and…

6. Determine the shear force (V) and bending moment (M) at X 6.1) X = 3.5 m and 4.5 m 7.5 kN/m Im 2m 15 kN 10 kN-m 9 kN/m 9 Im Im 1.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the same beam (orientation a) in Q1. If b=20 cm and h = 10 cm, and if the beam material has a maximum allowable stress of 100 MPa, then what is the maximum bending moment the beam can be exposed to? b Case (a) OI. 333.33 N.m O II. 20000 N.m III. 33333.33 N.m O IV. 1000 N.m Neutral axis
1- Use method of slope deflection method to draw the shear force and bending moment diagram A -3m 40 kN - 2m 2m 50 kN.m B 20 kN 2m2m C 10 kN/m 3m D 10 KN E -2m →
SITUATION 4 A simply supported beam, 6 m long, is subjected to a clockwise couple of 96 kN-m at the midspan. Assume flexural rigidity is constant. Determine the following. Deflection at Midspan a. 0 mm b. 6.9 mm 11. c. 27.7 mm d. 166.3 mm 12. Location of the Max Deflection a. 6.000 m b. 1.732 m c. 3.000 m d. 1.268 m 13. Maximum Deflection of the Beam. a. O mm b. 6.9 mm c. 27.7 mm d. 166.3 mm
Shear ane Moment by Area Method Show diagrams. Determine the maximum positive shear force in kN. Determine the maximum negative shear force in kN. Determine the maximum positive bending moment in kN-m. Determine the maximum negative bending moment in kN-m. Determine the point of inflection from point C in meters.
Determine the vertical displacement of end B of the cantilevered 6061-T6 aluminum alloy rectangular beam. Consider both shearing and bending strain energy.
calculate shear force and bending moment diagram
The beam shown below has internal hinges at points B and D. Assume EI is constant. Using conjugate beam method show the magnitude and directions of the support reactions (??,??,??,??,??), the elastic curve, vertical displacement at B, rotation just to the left of B, and the rotation just to the right of B.
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
Determine the inflection point. Then, sketch the bending moment diagram (BMD).
140 KN/m FIGURE 14 (B) 0.5 m 0.2 m Derive the expression for the shear force at segment AB. Derive the expression for the bending moment at segment AB. Compute the location of the point of zero shear. Compute the maximum moment of the beam. Determine the location of the point where bending moment goes from positive to negative (contraflexure point) from A.
From the beam shown with fixed end support at A and rollers at B... From the beam shown with fixed end support at A and rollers at B and C respectively, it carries a uniform load of 2 KN/m along span AB and a concentrated load of 12 KN at the mid span of BC. Using slope deflection method and constant value of El with E = 200,000 MPa and I = 400 x %D 106 mm4. What is the moment MBc in KN-m? Express your final answer in absolute value and use two decimal places. 2 kN/m 12 k A 24 m 8 m
(51) 5 m long AB rod is loaded with a 20.2 kN/m uniformly distributed load from End A to the midpoint as shown. The elastic modulus of the rod material is 210 GPa. The area moment of inertia of the rod is 837 cm. The slope at End B is most nearly: A. 0.55⁰ B. 1.25⁰ C. 1.50⁰ D. 2.00⁰ A 2.5 m 20.2 kN/m 5m B