6. Design Wide flange section of A992 steel to serve as a pinned- end main member column 30 ft long to carry an axial compression loads in a unbraced structure, based on AISC LRFD method. The dead load is 100 kips and live load is 150 kips at the top of the column. It is assumed that the column is braced with steel beams for both directions at height, 16 ft. Total beam reaction is dead load 30 kips and live load 90 kips at mid-height. Assume the bearing type connection with threads excluded form the shear planes, and double row of bolts is used. 14'-0" A992 steel 16'-0" P.

6. Design Wide flange section of A992 steel to serve as a pinned- end main member column 30 ft long to carry an axial compression loads in a unbraced structure, based on AISC LRFD method. The dead load is 100 kips and live load is 150 kips at the top of the column. It is assumed that the column is braced with steel beams for both directions at height, 16 ft. Total beam reaction is dead load 30 kips and live load 90 kips at mid-height. Assume the bearing type connection with threads excluded form the shear planes, and double row of bolts is used. 14'-0" A992 steel 16'-0" P.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Check the adequacy of the column shown in red colour with the 200UC59.5 section. The material is 300 Plus. Dead and live loads for all floors are the same as shown in Figure 1. All the support conditions are shown in the Figure. For bending about the minor axis, y, there is an intermediate secondary member that prevents its buckling and the column is simply supported. In case of buckling about the major axis, x, there is no intermediate lateral support and the column is pinned at the top and fixed at the bottom.
note: SN is equal to 18, topload will now be 118kN
A W36x210 can be used for Transfer Girder ‘A’ as shown in the elevation next page.Assume the LRFD loads on the ‘Transfer Girder’ are as follows:Pu= 200 kips from the column above. Assume also that the loads from self-weight of thewu = 2.0 kip/ft (girder self weight and beams framing into this transfer girder are equivalentto a uniformly distributed load). These loads are shown in the last figure.a) Check whether the W36x210 ‘Transfer Girder’ is adequate for bending and shear.Assume the unbraced length Lb =20 ft.b) Suppose that service loads, w and P, are both 50% dead load and 50% live load. Does theW36x210 satisfy a service live load deflection limit of L/480?
How much service live load, in kN/m, can be supported? The member weight is the only dead load. The axial compressive load consists of a service dead load of 45 kN 6.2m and a service live load of 90 kN. Do not consider moment amplification. Use NSCP 2015. W460x144 а. LRFD. b. ASD. br te Sy Z,J wt A tw Ix Sx Ty Zx Cw SECTION kN/m mm? mm mm| mm3 mm mm mm3 mm3 mm3 mm mm mm mm mm mm W460x144 1.41 18400 472 13.6 283 22.2 | 726 3080 199 83.6 591 67.4 3450 906 2440 4230
6-1.2-1: Find lightest W14 for L = 20', P = 600k E = 29,000ksi, Fb = 30ksi and Fv = 20ksi. 30. CONTINUOUS BEAM - TWO EQUAL SPANS-CONCENTRATED LOAD AT CENTER OF ONE SPAN Total Equiv. Uniform Load 13 p 8 P 2 R,= V₁.. 32 R R₂ R₁ R₂= V₁ + V₂. 11 p 16 V₁ R= V₁ V₂ Mmax (at point of load). M. (at support R)..... .......... Amax (at 0.480 / from R.).... M Imax Shear Moment M₁ V₂ ********* ***************** 11 = 11 P 32 - 19 p 32 13 64 = 3. Pl PI 32 0.015 P³ El
A W 16 x50 is used as a beans to carry a uniform we and dead load including own weight of 37 kN/m and an axial tension load of T acting through the centroid, of the member. It has a simple span of 5.7 m. The compression flange of the member is laterally supported against local buckling.Use A 36 steel, Fy = 248 MPa.Properties of W 16x 50A = 9483.85 mm^2d= 412.75 mmbf= 179.65 mmtf= 15 95 mmtw= 9.65 mmSx= 1324 × 10^3 mm^3Sy = 172 x 10^3 mm^3 Questions:Determine the Safe axial load T that the beam could carry Hint Answer: 432.69 KN
The W section is reinforced at top and bottom flanges by a 250 mm wide by 16 mm thick plate is used as a column with with a length of 5.0 m. Determine the safe axial load the column can carry using AISC specifications with Fy = 345 MPa when: a) column ends are fixed b) one end of the column is fixed; the hinged c) both ends are hinged 200 mm CIVIL ENGINEERING STEEL DESIGN tw 13.41 = 8.08mm 250 mm
Use NSCP 2015. The beam shown has continuous lateral support of both flanges. The uniform load consisting of 50% dead load and 50% live load. The dead load includes the weight of the beam. Used grade 50 steel. 6 k/ft |--0-0²- -18'-0"- fo 4-6- -6'-0" 1. Considering LRFD. Which of the following most nearly gives the design load Wu? 2. Considering LRFD. Which of the following most nearly gives the maximum negative design moment, Mu in ft-kips? 3. Considering W12x35 beam section, The section is 4. Considering ASD the W12x35 beam section, Which of the following most nearly gives allowable strength in ft-kips
The frame shown below is subjected to uniformly distributed load of 2.6KP.. Determine the maximum moment of member BF (assume simple beam support) A E, 1.5m F 1.5m 351 C 1.5m H 3m B
Determine the safe load P that the member below can carry using ASD and LRFD. The column is W18x60, A-50 steel. The column has an intermediate brace in the weak direction as shown. W18x60: A = 11400mm^2Rx = 189.64mmRy = 42.82mmFy = 350 MPa
please help
a uniform load w across its full length. Use this beam to respond to problems 4 through 8. 4. The support reaction at 8 equals (a) aw (b) 2w (c) w/2 (d) 2aw (e) None of these