6. A scientist conducted an investigation to investigate the iron (III) thiocyanate equilibrium. The initial concentration of both iron and thiocyanate ions was 3.57 × 10-4 mol L-¹. When the system reached equilibrium, the concentration of iron thiocyanate was 1.58 × 10-5 mol L-¹. Calculate the value of Keq at this temperature. (3 K)

6. A scientist conducted an investigation to investigate the iron (III) thiocyanate equilibrium. The initial concentration of both iron and thiocyanate ions was 3.57 × 10-4 mol L-¹. When the system reached equilibrium, the concentration of iron thiocyanate was 1.58 × 10-5 mol L-¹. Calculate the value of Keq at this temperature. (3 K)

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Solid PbBr2 (Ksp = 6.6 x 10-6) added to a solution of AgNO3, which results in the formation of solid AgBr (Ksp =5.5 x 10-13). For the following question, enter your answer to the appropriate number of significant figures. When inputting an answer in scientific notation, use “e” notation rather than multiplying by a power of 10. For example: 0.00031 = 3.1e-4. Do not write 3.2x10^-4. Do not include units in your answer (but do consider them when solving the problem!) Calculate Koverall using the balanced equation.
Can you solve the problems below, there's 2 pages. The page with the number 1 on the top corner is the first page. That page has only two questions located under the picture of the beakers. The other page has a number 4 at the top right corner and that's the 2nd page. On the second page please fill in the blanks and solve the % error. Thank you and please show all your work.
Before investigating the scene, the technician must dilute the luminol solution to a concentration of 5.00 x 10-2 M. The diluted solution is then placed in a spray bottle for application on the desired surfaces. How many moles of luminol are present in 2.00 L of the diluted spray? Express your answer with the appropriate units.
Below is a picture of a 10-fold dilution series. What is the dilution factor of tube # 3? Write as both a fraction and scientific notation. i mL EC 9 mL 9 mL 9 mL HIO 9 mL ecterial Sampie TLbe #1 Tube e2 Tube #3 Tube #4
So I had to measure the diameter of a sphere with vernier calipers. The radius was 9.55 mm. I got the volume of the sphere being 3648.368 by using the equation below. But here's the instructions for it. I don't know how to convert this number into the other units of measurement. Calculate the volume (in mm3) of the solid using the formula: Volume = 4/3 x π× radius3 Round your answer to the correct number of significant digits and record it with the correct units. Convert the volume in mm3 to cm3 and then to in3.
15:32 Sun May 2 Done < AA A session.masteringchemistry.com
> In a typical quantitative analysis, which step is the most crucial? What part will make or break the result? Why?
Perform the calculations and determine the absolute and percent relative uncertainty. Express each answer with the correct number of significant figures. To avoid rounding errors, do not round your answers until the very end of your calculations. 7.8 (+0.3) – 2.03 (±0.02) = absolute uncertainty: percent relative uncertainty: 8.24 (+0.04) × 0.012 (±0.001) = absolute uncertainty: percent relative uncertainty: %
Suppose you were measuring out an organic liquid, and some of it is evaporated after you have performed the volumetric measurement while you are weighing out the sample. What effect would this have on the densities you calculated? Will you overestimate or underestimate the density of the liquid? Would this cause poor accuracy, low precision, or both? Explain briefly.
A student dissolves a Jefferson nickel to make 100.00 mL of solution in a volumetric flask. The student takes a 5.00 mL aliquot of the first solution and dilutes it to make 100.00 mL of a second solution. The student places a sample of the second solution in a cuvette for analysis using spectrophotometry. The molarity of the copper solution in the cuvette was determined by spectrophotometric analysis to be 2.90 x 10-2 M Cu. Calculate the mass of copper in the Jefferson nickel used to make the first solution. Use the diagram to help visualize the dilution process. WE IN GOD TRUST 100 mL LIBERTY 200 5 mL 100 mL cuvette
Number 1. I get 33 liters. No idea what I did wrong as I calculate one mole of aluminum present one mole of hydrochloric acid present giving me 1.5 miles of hydrogen plug that in to pv= nrt. With p= 1atm. T = 273.
You are given four values (1.033, 4.157, 1.05, and 4.6) and asked to conduct calculations on them. You perform a series of mathematical operations using the values and make a table that includes the calculated value as displayed on your calculator: Mathematical operation Value displayed by calculator 1.033 +4.157 +1.05+4.6 10.8400 1.033 x 1.05 1.08465 4.157 - 1.05 3.10700 4.157/31.0341 0.133949 4.6/31.0341 0.148224 Round each of the values displayed by the calculator to the correct number of significant figures, and place the value in the bin that correctly indicates the number of significant digits you rounded to. Drag the appropriate items to their respective bins. » View Available Hint(s) Reset Help 10.8400 1.08465 3.10700 0.133949 0.148224 1 significant figure 2 significant figures 3 significant figures 4 significant figures