6. A reinforced concrete T Beam has a width of 800 mm and a thickness of 50 mm. It has an effective depth of 300 mm and is reinforced at the bottom with a total steel area of 1800 mm². If the web thickness is 200 mm, fc' = 20 MPa, and fy = 400 MPa, compute the (a) total compressive force of concrete (b) value of the area subjected to compressive stress (c) ultimate moment capacity of the beam %3D %3D

6. A reinforced concrete T Beam has a width of 800 mm and a thickness of 50 mm. It has an effective depth of 300 mm and is reinforced at the bottom with a total steel area of 1800 mm². If the web thickness is 200 mm, fc' = 20 MPa, and fy = 400 MPa, compute the (a) total compressive force of concrete (b) value of the area subjected to compressive stress (c) ultimate moment capacity of the beam %3D %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A TIMBER BLOCK "B x B" mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A "B" mm AND 't' mm THICK STEEL PLATES. DETERMINE THE THICKNESS 't' SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY. B t B t PROB 04
4. An interior reinforced concrete slab has to be designed to support a live load and a dead load in addition to its own weight based on the following specifications: The slab is one-way and simply supported with a span of 12 ft. The live load on the slab is 200 psf. The dead load on the slab is 100 psf. Your design will use concrete compressive strength fe= 3000 psi and steel yield strength of fy = 40,000 psi
a simply supported beam 300mm wide, 500mm deep and spans 5.7m supports a service super imposed dead load of 8kN/m and service live load of 7kN/m. concrete strength f'c=21MPa and steel yield strength fy=415MPa. concrete cover to bar centroid is 70mm. determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015.
Hello, please solve the question about reinforced concrete from the sixth and seventh chapters of the third civil stage
A simply supported beam is reinforced with 5-p25 mm at the bottom and 2-020 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN -m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
A laminated beam is composed of four (4) planks, each of 150 mm x 30 mm, glued together to form a section 150 mm x 150 mm. The allowable shear stress in the glue is 850 kPa, the allowable shear stress in the wood is 1050 KPA, and the allowable flexure stress in the wood is 10 MPa. Determine the maximum uniformly distributed load which can be carried by the beam on a 45 m simple span.
Please answer as soon as possible
using the table below, answer the question
A typical grade beam 300 x 800 is reinforced with 2 - 25M bars and the cover is forconerete cast and permanently exposed to the earth, (f', =30 MPa) Determine the following: (a) the size of the stress block "a" (b) the bending moment “M," (c) the c/d ratio (d) the type of failure (brittle or ductile) based on part (c) (e) check Asmin (equation 2.7) (Code 10.5.1.2) (f) maximum As permitted based on ductile failure (g) determine maximum bar size (2 required) from Table 1.5 based on part f) (h) check spacing requirements 's' Table 2.6 based on part g) (i) check if skin reinforcement is required Table 2.9 and fy = 400mpa please solve asap %3D
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
Asiacell lln. H.W. No.1 For the simply supported solid one way reinforced concrete slab shown in the figure below having a span of (L= 4m), check the following requirements using strength method: a- Slab thickness b- The spacing between reinforcement for main and shrinkage reinforcement c- The actual reinforcement with minimum reinforcement d- Calculate ultimate resisted moment that can be withstand by the slab e- Determine the ultimate uniformly distributed load carried by slab. f = 25 N/mm2 fy=420 N/mm² + 10mm@s00mm shrinkage h=200mm -L=4m- $12mm@200mm main