(6) A small single-cylinder, two-stroke cycle SI engine operates at 8000 r.p.m. with avolumetric efficiency of (0.85). the engine is square (bore-stroke) and has a displacement3of 6.28 cm the fuel-air ratio FA=0.067 . calculate :-m(a) Average piston speed.sec(b) Flow rate of air into engine. kgsec(c) Flow rate of fuel into engine. (kgsec(d) Fuel input for one cycle. kgcycle(d) 4.22×10-7ANS: (a) 5.33, (b) 0.00084, (c) 5.63×107

The Speed of Engine/crank shaft N=8000RPMtotal displaced volume Vd=6.28cm3Volumetric efficiency…

Answered: (6) A small single-cylinder, two-stroke…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) The pressure, volume and temperature at the beginning of compression of a four stroke petrol engine are 105kN/m²,0.0005m³ and 25°C respectively. The maximum temperature of the cycle is 1400°C. The volume ratio of the engine is 8:1. i) Calculate the mean effective pressure in the cylinder.
A diesel engine operating an air standard diesel cycle has 20 cm bore and 30 cm stroke the clearance volume is 420 cm cubic if the fuel is injected at 5% of the stroke. Find the air standard efficiency.
An automobile have a three-liter SI V6 engine that operates on a four-stroke. The compression ratio is 10.5, the length of connecting rod is 16cm, and the engine is square. At this speed, combustion ends at 20° a TDC. The connected to a dynamometer which gives a brake output torque reading of 200 N.m at 3600 r.p.m. at this speed air enters the cylinder at 85 kpa and 60℃ and the mechanical efficiency of the engine is 85%. Calculate: 1- Clearance volume of one cylinder. 2- Piston speed at the end of combustion. 3- Volume in the combustion chamber at the end of combustion. 4- Friction mean effective pressure. 5- Brake output per displacement.
internal combustion engine. please help as much as possible
Task 1 A V-8 Spark ignition engine has a 10 cm diameter bore and 10 cm stroke. At the beginning of compression process air is at 95 KPa and 27 Degree Celsius. 750 KJ/Kg of heat was transferred to air during heat addition process. The compression ratio is 8. Consider the variation of specific heats with temperature. A. Describe with the aid of diagrams the operational sequence of four stroke spark ignition engines B. Explain the mechanical efficiency for ideal otto cycle of two and four stroke engines C. What is the difference between four and two stroke spark ignition engines? D. Explain the relationship between thermal efficiency (n) and compression ratio (r). E. Why are high compression ratios not used in spark ignition engines? F. Determine the net-work output per cylinder per cycle (KJ) G. Determine the efficiency of the engine. H. Determine the Mean Effective Pressure (kPa) I. What is the Power Output of the engine running at 2000 rpm. Task 2 A compression ignition engine operates…
(a) Chevrolet Silverado 6.2-liter, V8, four-stroke cycle SI engine is designed to have a maximum speed of 6500 RPM. At this speed, volumetric efficiency is 88%. The engine is equipped with a four-barrel carburetor, each barrel having a discharge coefficient of CD, = 0.95. The fuel used is gasoline at AF = 15:1 with a density of 750 kg/m. Determine: (i) Minimum throat diameter needed in each carburetor venturi. (ii) Fuel capillary tube diameter needed for each venturi throat.
A single acting two-stage air compressor deals with 4 m^3/min of air under atmospheric conditions of 1.013 bar and 15°C with aspced of 250r.p.m. The delivery pressure is 80 bar. Assuming complete inlercooling, find the minimum power required by the compressor and the bore and stroke of the compressor. Assume a pistonspeed of 3 m/s, mechanical efficiency of 75 percent, and volumetric efficiency of 80 percent per stage. Assumethe polytropic index of compression in both the stages to be it = 1.25 and neglect clearance.
Q - The rotor of an impulse turbine is 60 cm diameter and runs at 9,600 r.p.m. The nozzles are at 20° to the plane of the wheel, and the steam leaves them at 600 m/sec. The blades outlet angle are 30° and the friction factor is 0.8. Calculate the power developed per kg of steam per second and the diagram efficiency.
Compute for the discharge pressure in bar of a single-acting air compressor if the piston-arrangement has a clearance of 7.5% and a volumetric efficiency of 75%. The isentropic compression has an intake pressure of 750 mmHg a. 4.46b. 5.57c. 6.68d. 7.79

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS