6-39. Draw the influence line for the force in (a) member HI, (b) member FI, and (c) member EF. L K H 4 m A. C -3 m--3 m- B E F -3 m- 3 m- 3 m

Q: Draw the influence line for the force in member CD.

A: During the movement of a concentrated force across a member, the influence line represents…

Q: Draw the influence lines for the forces in the members identified by an "x" of the tru shown in the…

A: An Influence line Diagram shows the influence of effect due to load on the reactions, shear force or…

Q: B fm fm Draw the influence line for the beam Use Müller-Breslau's Method 1 Reaction at A 2 Reaction…

A:

Q: Draw the influence lines for the force in member GC of the bridge truss. H G 6m -6 m- B -6 m (a) 6…

A:

Q: Draw the influence line for shear force Vc. Enter the magnitude of your and G influence line when…

A:

Q: Draw the influence line for the vertical reaction at A and the internal bending moment at C for the…

A:

Q: Construct the influence lines of each truss member. H 4 m В E 6@3 m = 18 m

A: An influence line for an obtained member, like reaction, axial force, shear force, or bending…

Q: L K H 8 ft A 台 B - 8 ft E 8 ft- 8 ft- -8 ft

A: Solve and draw the influence line for the force in member JE.

Q: Maximum axial force on EF.

A:

Q: 6-1. Draw the influence lines for (a) the moment at C, (b) the vertical reaction at A, and (c) the…

A: Influence lines  using the Muller Breslau Principle.

Q: 2. Determine the smallest moment of inertia required for the beam shown, so that its maximum…

A: Please upload one question at a time

Q: Question 2: Draw the influence line for the force in member DK. L K H 1.5 m B] -2 m-2 m--2 m--2 m-…

A:

Q: Draw the influence line for (internal) bending moment MĘ. Enter the magnitude of your influence line…

A:

Q: Draw the influence line for (a) the vertical reaction at A, (b) the shear at C, and (c) the moment…

A: (a) Let the unit load is acting on the beam. Consider the following figure. In each case,…

Q: -2m 2 m F B E A D - 2m – -2 m -2 m 2 m -2 m

A: We have draw influence line for shear panel BC and moment at D.

Q: Draw the influence line for the forces in members: UU2 UiL2 and U2Ls 30

A: Influence line diagram for force in member U1U2Consider the free body diagram shown in figure by…

Q: d live load of P kN. Determine (a) the maximum positive (upward) reaction at B, (b) the maximum…

A: For the above beam, Assume W1=87N/mW2=4kN/mP=3kN

Q: Draw the influence line for (internal) bending moment MA. Enter the magnitude of your influence line…

A:

Q: Draw the influence lines for (a) the vertical reaction at A. (b) the shear at C, and (c) the moment…

A: Given data in question  Span member length  To find out  ILD NOTE We will draw ILD using Muller…

Q: Draw the influence lines for (a) the ve (b) the shear at C, and (c) the moment a

A:

Q: Draw the influence line for the force in (a) member KJ and (b) member DK.

A: Question is based on the truss . Length of members are given in the question . Influence line…

Q: Question 2: Draw the influence line for the force in member DK. L K H A 1.5 m B] -2 m D F -2 m -2 m…

A:

Q: 2. Draw the influence line for the force in (a) member EH and (b) member JE. M C B D E F m-4 m 4 m 4…

A: Given :

Q: L K opogo H AM D E 6 ft 6 ft 6 ft 6 ft 6 ft-6 ft- G 8 ft

A:

Q: QI/- Draw the influence lines for (a) the vertical reaction at G, (b) the vertical reaction at D,…

A: Given data in question  Span member length  Overhanging beam  To find out  ILDs  Note We will draw…

Q: Draw the influence line for the force in member GB of the bridge truss shown. SHOW THE COMPLETE…

A:

Q: Delermine maximum upward reaction at c and A if there is dO KN point load, as KN/m uniformiy…

A:

Q: Problem 5: Determine the roller reaction (in kips) at A of the frame shown. 5 kip 7 kip 10 kip 2 kip…

A:

Q: Determine the reaction at support C. Support C is fixed. W= BKN W- BN L-3m. -3m. L-6m

A:

Q: The ordinate at point D in the influence line of Mc for the beam shown equals Hinge Hinge A B D EA…

A: Influence line is a graph depicting Reactions, Bending Moment or shear values at a section, when a…

Q: 6-13. Draw the influence lines for (a) the moment at C, (b) the shear just to the right of the…

A: The question is based on a section supported on hinge and roller support. The length of the span is…

Q: (2) Draw the influence lines for (a) the vertical reaction at B, and (b) the moment at E. Assume the…

A: The continuous beam with an internal hinge is shown in the above figure. We have to find out the…

Q: Draw the influence line for the force in member HC, IC and IJ of the bridge truss shown below. H B D…

A:

Q: 15m 3m 2m B A 4m Em D 100KN

A:

Q: Draw the influence line for the force in member BF, then determine the maximum force (tension or…

A:

Q: P 1.0 C D E 6 @3m = 18 m

A:

Q: Draw the influence line for shear force VE. Enter the magnitude of your and G influence line when…

A:

Q: Draw the influence line for the force in member GD, then determine the maximum tensile force that…

A: Given a truss carrying uniform live load of 3 kN/m that acts on the bridge deck along the bottom…

Q: Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the moment…

A: Lo = 5 +4 + 7+3 = 19

Q: Draw the influence line for member GH and interpret the diagram. H 15 ft A D B C E 4 @ 20 ft = 80…

A: Finding out the influence line diagram for member GH.

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.