500 sq mm в 300 sq mm 400 sq mm A D 10KN 40 KN 50 KN- 20 KN 200 mm 600 mm 300 mm

Q: Calculate the maximum tensile and compressive stresses in the brass and aluminium.

A: A composite beam is formed with more than one material to increase its load resistive strength. When…

Q: Lever Problems - effort Resistance and Mechanical Advantage  R = 50 Lbs Length FE = .75 inch…

A: GivenR=50lbsFE=0.75inFR=12in

Q: Determine the value of: Vertical Reaction at A, Vertical Reaction at B, Vertical Reaction at E,…

A: Draw the free-body diagram of the given truss.

Q: Find the following. Show complete solution.

A: The given diagram is here, Section 1:- A rectangle OABC, whose sides are 120 mm and 80 mm Section…

Q: * B2/(b) X-bar Y 3 ст - 0.952 y=kx? 8 cm 0.952 -2.413 7 cm 6 cm 2.431 - 1.026 1.026

A: Given: For curve, At x = -7, y = 0 and at x = 0, y = 8 cm,

Q: 1 kN 2 kN 2 kN 2 kN 1 kN H 0.46 m F D 2.62 B I A C| E G| 2.4 m 2.4 m 2.4 m 2.4 m Figure 2

A:

Q: Consider the beam shown in FIGURE P2-68 of the textbook. What is the magnitude of the resultant…

A: Moment:the ability of the force to twist the body about a point is known as the moment it is…

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: IF e = 60 3 T:5 KN, determine the magnitude of the resultreunt force acting on the eye bott aud it's…

A:

Q: 2- Draw Shear Stress vs. Strain Diagram for steel specimen

A: To draw stress vs. strain diagram for steel specimen

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: 120 mm 60 mm 90 mn D 80 mm C 45 mim 480 N

A:

Q: 1. Solve for the total reaction at support A. O 20 kN O None of the above 80 kN 40 kN a. Determine…

A:

Q: 300lb -800lb 30 30 -200lb 600lb FORCE Ibs F= F.Cos(e) F = F.Sin(e)

A:

Q: What is the magnitude of force F ? (Please solve in paper with diagram)

A: Given:Find:The magnitude of the force F.

Q: R=50 Lbs Length FE75 inch Length FR 12 Inches Calculate E (Lbs) Calculate MA

A: Draw the free body diagram.

Q: 400 N 3 m A, 8 m 4 m D 1200 N

A:

Q: Date Find the MOVEMENT OF INERTIA about eentroidal x-axis and centroidal y-aric af egiven Figure

A: Before to calculate moment of Inertia, we have to calculate centroid of the given figure.Since,…

Q: Q2/ Determine the diameter of the rivets and the forces in all rivets. Take Tallowable as 60 MN/mm².…

A: Given Datan=8θ=30°F=40kN

Q: 60° looks 50 g C 80° 6 G 30 VO 38 66 f 7 ft 78 ) ។ Yo >15 3ft 4ft 2ft Find force for all member? E

A:

Q: -800 Dimensions in mm F1 600 F2 F3 900 -560--480- What is the x component of F1=701 N?

A:

Q: 150 mm y30 mm 120 mm Area 2 X2 30 + (2b/3) 100 mm X3 = 150- (4r/3n) Area1 y2 TArens y3 120 mm 130 mm

A:

Q: 6 kN 45° 5 kN C B A 45° 6 kN 5 kN 10 kN 0.75 m 1.50 m 1 m

A: Given data  E= 200GPa Yield strength = 345 MPa  Find the displacement of point B and A

Q: A 0.8 Mg car travels over the hill having the shape of a parabola. If the driver maintains a…

A:

Q: If the load applied at the handle, P = 45 N, calculate the force that results on the piece held in…

A: Given That P FBD

Q: Q// Determine the resultant force in figure bellow, and specify where it acts measured from point B.…

A:

Q: Start this problem on a new sheet of paper The structure shown is supported by a pin at A and roller…

A: Given data is

Q: Pin T A 3 m 4*う B 100 N 100 N Fac 4m 50 N F3c sc '50N Rolfer 19501 4 m Roler FA FAB Pac 3 Ray R Ax…

A: to determine -  Fab , Fbc , Fca

Q: The design specifications for the steel shaft AB require that the shaft acquire a strain energy of…

A:

Q: 3: For the beam shown in Figure (3), given INA = 1.- 10 mm, calculate the transverse shearing stress…

A: INA=1×106 mm4 simply supported beam as shown below At left support , sectional area given as shown…

Q: Q2 A small marble at point A of mass 0.5 kg as shown in Figure Q2 is release downward with an…

A: Given data: VA = 2 m/smass of body = 0.5 kgtan θ = 34 θ = tan-1(34) = 36.87°

Q: Determine the distance to the neutral axis from the top surface of the cross sectional shape shown…

A: Given: The cross-section area is given below,

Q: Consider the beam shown in FIGURE P2-68 of the textbook. What is the direction of the resultant…

A:

Q: Determine the position of the x-centroid in mm.

A:

Q: 80 kN 40 kN 60 kN -10 kN/m A B 2 mim. 3 m 3 m 2m 1 m (b) 10 k I k/ft B 12 8' (b)

A:

Q: A mechanism carries a constant load P applied to the seat as shown. For the angle 8, determine the…

A:

Q: Find: FAB, FAI, FBC, FBI, FCD, FCF, FCG, FCI, FDE,FDF, FEF, FGH, FGI,FHI

A: Draw the free-body diagram of truss.

Q: From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be the…

A:

Q: 0.54 kN A 200 mm C A L 1.35 kN D E 500 mm 400 mm 0.54 kN B -300 mm

A: Given