500 kg of air is supplied per minute to an auditorium maintained at 21°C and 40% RH. The outside air at 5°C DBT and 60% RH is first passed over heating coils and is heated until its WBT is equal to the room WBT. It is then passed through an adiabatic saturator and is finally heated to 45°C before being supplied to the room. Determine a) the heat added in both the heating coils b) the mass of water evaporated in the air washer

Q: In a psychrometric process, the sensible heat added is 30 kJ/s and the latent heat added is 20 kJ/s.…

A: Given: Sensible heat=30 kJ/s Latent head added= 20 kJ/s To find:- Sensible heat factor

Q: QA piston/cylinder arrangement, contains CO2 at 300 kPa, 250°C. The 40-kg piston has a diameter of…

A:

Q: A piston-cylinder device initially contains 2 kg of refrigerant-134a at 100 kPa and 20°C. Heat is…

A: Given data: m=2 kgP1=100 kPaT1=20°CP2=120 kPaT2=80°CTo=25°CPo=100 kPa Need to determine the work…

Q: Refrigerant-134a enters an adiabatic compressor at -26°C as a saturated vapor at a rate of 0.45…

A:

Q: Air enters an adiabatic nozzle at 230 kPa, 600°C with a velocity of 60 m/s. The air is at 70 kPa,…

A: A nozzle is a smooth-varying cross-sectional channel that converts working fluid pressure energy…

Q: 4.) Steam undergoes an Isentropic process where it is initially at 1.30 MPa and 200 C then it…

A:

Q: An air handling unit receives re-circulated room air at 23 oC DBT and 50% RH and flow at 2 m3/s, and…

A:

Q: Air at dry-bulb temperature of 75°F and wet-bulb temperature of 65°F is heated to 250°F and fed to a…

A: As per the question, conditions are plotted on the Psychometric chart, and determined the required…

Q: 2. A rigid tank initially contains 2.75 L of air at 125 kPa and 27°C. An electrical resistance…

A: The volume of the tank is V=2.75 L The initial temperature is T1=27°C=300 K. The initial pressure is…

Q: Moist air of 0.1 kg/s enters a heating coil at t=15°C, d = 10 gw/kgda, and exits it at /= 50°C.…

A:

Q: A well-insulated 3-m 3 4-m 3 6-m room initially at 7°C is heated by the radiator of a steam- heating…

A: To find Determine the average temperature of the air after in 45 min.GivenThe volume of the room,…

Q: moist air supplied to an air conditioned room is 600 m3 /min. The External conditions are 34.4°C DBT…

A:

Q: An adiabatic condeser receives 100 kg/s of steam at 92% quality and 6- kPa. The steam leaves at 60…

A:

Q: 17. A piston-cylinder device with a set of stops initially contains 0.3 kg of steam at 1.0 MPa and…

A: Given:m=0.3 KgP1=1.0 MPav1=0.30661 m3/Kgv2=0.6*v1h2=2950 KJ/Kg

Q: Directions: Identify the condition of the following steam and write whether if it is at -saturation…

A: Given State To find Identify the property

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: 17. A piston-cylinder device with a set of stops initially contains 0.3 kg of steam at 1.0 MPa and…

A:

Q: The system shown in (Eigure 1) is called Russell's traction Figure 60⁰ 1 of 1 Part A if the sum of…

A: Given :The sum of downward forces exerted at A and B by the patients legs is 36.2 lbFind:weight W

Q: QA piston/cylinder arrangement, contains oxygen at 300 kPa, 250°C. The 40-kg piston has a diameter…

A: Given, P1 = 300 kPa T1 = 250 C = 523 k mass of piston (M) = 40 kg diameter of the piston (D) = 0.15…

Q: Required information Problem 08.034 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS - Refrigerant…

A:

Q: An isentropic air compressor takes 150 m/min of air in at 10°C and 100kPa and compresses it to 1000…

A: Given: Flow rate (Q)=150m3/min Inlet temperature T1=10°C or 10+273=283K Inlet pressure P1=100kPa…

Q: 50 btu of heat are added to a gas at a constant temperature of 600 F. How much of this heat is…

A: Given Data: The heat added at temperature TH  = 600 F is Q = 50 Btu. The refrigerator temperature…

Q: Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam…

A: Given:-  To Find:-  The enthalpy ( h2 )of bled steam entering the open feed water heater.

Q: In a heat engine, 2.60 mol of a monatomic ideal gas, initially at 4.00 atm of pressure, undergoes an…

A:

Q: Compare Isentropic Process and Polytropic Process.

A: To Answer:- Isentropic Process and Polytropic Process

Q: 1. Boiler. Steam at 40 bar, 350°C, is generated in a boiler at the rate of 50,000 kg/h from feed…

A: Given dataFeed water temperature = 130 °CSteam mass flow rate = 50000 kg/h = 13.889 kg/sSteam…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Given:Initial pressure of the refrigerant, P1=100 kPaVolume flow rate, Q=0.6 m3/minFinal pressure of…

Q: An insulated tank that contains 2.6 kg of O2 at 15°C and 300 kPa is connected to a 2-m³ uninsulated…

A: Given data as per the question Mass of Oxygen =2.6 kg The initial temperature of oxygen =150 c The…

Q: How to measure the property entropy?

A: Entropy It is the quantitate measure of randomness in a system. The concept deals with the heat…

Q: Copy of It is proposed to have carbon dioxide (CO2) gas pass through an uninsulated nozzle. The CO2…

A:

Q: The operation of turbine is to harvest energy from the high temperature steam. Consider a scenario…

A:

Q: 652) A piston-cylinder contains 500 g of R-134a at 1200 kPa and 80 °C. A resistance heater within…

A:

Q: 16. Steam at 2 Mpa and 250°C in a rigid cylinder is cooled until the quality is 50%. * Find the heat…

A: Given data,At 2mPa and 250∘C,Quality, x= 50%V=0.11144m3/kgu=2679.6KJ/kgAt 2mPa (saturated),Vf=…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: A cooler is used to cool water from 30°C to 5°C. The cooler has steady- flow, and the mass flow rate…

A: Given:Initial temperature of water, Ti=30°CFinal temperature of water, Tf=5°CMas flow rate of water,…

Q: A refrigeration plant works between the temperatures limits of -5°C and 25°C. The refrigerant is CO2…

A: Write the expression of the theoretical COP.   COPtheo=TcTh-Tc=-5+27325+273 K--5+273=8.93…

Q: rat 40°C dbt and 55% RH is passed over a t exit from coil the air is saturated and itst leaves at…

A: given:

Q: In figure below compute the net force exerted on the hemispherical shape located at the bottom of…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: Question 2: An air-standard set of processes with constant specific heats is executed in a closed…

A:

Q: A 0.04-m3 tank initially contains air at ambient conditions of 100 kPa and 22°C. Now, a 17-L tank…

A: Given, Volume of air Va1 = 0.04 m3 Volume of water Vw2 = 0.017 m3 Initial temperature of air Ta =…

Q: 0% fresh air at 40°C DBT an nd 50% RH. The air leaves ti Cal cooling load and room heat

A: given:

Q: . How much heat must be released p completely turn 1.0-kg steam with n initial temperature of 120°C…

A:

Q: Air at 20 ° C and 50% RH is channeled into the heating coil so that the temperature of the dry ball…

A: Given data:

Q: The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal…

A: