5.The values of Y and Y2 of the trapezoidal load are Y 1 V Y 2 16.67 kN 4m 13.33 kN a)Y=8kN/m, Y2=3kN/m b)Y=10KN/m, Y;=5kN/m c)Y=8kN/m, Y;=0 d)none of the previous choices

Q: What are the two most common systems of units?

A: Given Data⇒ systems of units Problem statement⇒ Problem says What are the two most common systems of…

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: A bcc (111) surface has the following (3x1) adsorbate structure: Select all of the following LEED…

A: Solution: Given Data:

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: TC Sin2 * cos' z 2. sin? dx

A:

Q: part1 and part 2 are correct

A: Process 3-4s : Isentropic expansion process.Process 3-4a : Actual expansion process.Process 4a-1 :…

Q: 3 just wearing his suit so you know he's an astronaut, is holding a space space chest along with the…

A: M = 761 g  h = 0.6m          a     distance between E to B         d = 0.7 2+0.62        d =0.92 m

Q: A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below.…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: The triangular lamina with base = 80 mm, height = 60 mm.  The Iyy value is _____________ mm4 Select…

A: Given data: base (b) = 80 mm height (h) = 60 mm Need to determine the moment of inertia about y-y…

Q: Members ABC and DEF are joined with steel links (E = 200 GPa). Each of the link is made of a pair of…

A:

Q: What unit is the 0.000931 ?

A: Torsion equation is given by, TJ=τr=GθLwhere,T = torque acting or applied in N-m or N-mmJ = polar…

Q: Where did the 0.10472 rad/s come from?

A:

Q: To measure the angles, engineer square is used. Select one: True False

A:

Q: 100 mm- 11.5 mm 7.5 mm N A 225 mm 11.5 mm (a)

A:

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: The equation of the unit circle is _______________.

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: 28 cm a? 100 cm 30° V 15 cm

A:

Q: What is the length and wall thickness of the vertical bear

A: For figure 2,  drawing and the type of symbols present

Q: Fload/8 Fload/4 ffort = Fload/8

A: According to the details provided in the question, we need to calculate  we need to find all forces…

Q: how can I get the 85 α

A:

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: What is the average force magnitude?

A:

Q: For figure (4): The ring is subjected to two forces (F, and F2). Suppose that the resultant force…

A: Given data:

Q: 40 7 slug 110 dyne

A: given:

Q: Crossed center lines are used in the .. . view Longitudinal Horizontal Circular All

A: Solution:

Q: True or False? All rectangular x-sections less than 12-inch in width and less than 0.23-inch in…

A: The minimum width for the all rectangular section to be known as strip is 12 inches while the…

Q: Calculate the number of degrees of freedom The value must be a number 11 Calculate the number of…

A: Full joint is the joint which has area or surface contact, and half joint is the joint which has…

Q: A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has…

A:

Q: 5と 2' 111ド 7K 8'一 16- 251

A:

Q: What is the location of FR, i.e., the distance d? A M 3 m 3 m F. R B

A:

Q: A4B) Force.. represents value of the force. O a. sense O b. magnitude O c. point of application O d.…

A: This question is from classical mechanics.

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.