5.87 Calculate the torque required to drive the pump shown inFig. P5.87 at 30 Hz and to deliver 20 °C water at 3.0 m³/min.Absolute velocity, V₂8 = 45°R₁₂ =0.13 mAbsolutevelocity, V₁R₁0.065 mImpellerFigure P5.87b₂ = 1.0 cm30° = 01b₁₁ =3.0 cm

Answered: Image /qna-images/answer/303ea73d-bbc6-49ca-ba78-a6794d8b7f98.jpg

Answered: 5.87 Calculate the torque required to…

5.87 Calculate the torque required to drive the pump shown in Fig. P5.87 at 30 Hz and to deliver 20 °C water at 3.0 m³/min.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(B) Two similar centrifugal pumps are connected in series. The theoretical head- discharge relation of Pump#1 is given by: h, = 5.3 – 0.58Q and that of Pump#2 is given by: h, = 7.7 + 0.22Q. At a specific operation conditions, the head of these combined pumps is 12 m. Estimate the followings: (i) The head of each pump (ii) If the flow out of this system is completely blocked while the two pumps still running, what is the resulting total head of the system? (iii) If the two pumps rotates with same speed, how many pump#2 is bigger than pump#1?
Given: Two (2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure = 4.95 Bars Suction Pipe Dia = 450mm Discharge pipe Dia = 480mm Velocity of Water = 4.25 m/s Solve: Total Head, Pump1 & 2 individual head and if Pump 2 is 9.5% less than Pump 1 and QT = Total Flow Rate
You and your workmate are choosing pumps for your design. You've already decided which centrifugal pump you will use. The next thing you would think about this time would be the shape of it's impeller blades. The impeller in your design would have a revolution of 565 rpm, will have a volume flow rate of 11.7 gals per min and will (discharge) head of 2222 cm. Your coworker said that axial flow pump is your choice. Would you agree? Why or why not? Prove it.
4. A centrifugal pump delivers 1500 L/min of water from an initial pressure of 156 kPa to a final pressure of 328 kPa. The area of the inlet pipe is 315 cm² and the area of the discharge pipe is 80 cm?. Solve for the power input to the pump, kW.
Q Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
Hydrodynamics pumps 5. A centrifugal pump has r1 = 6 in., r2 = 12 in., b1 = 3 in., b2 = 2 in., β1 = 20°, β2 = 10° and rotates at 1200 rev/min. If the fluid is water at 60°F, estimate the theoretical (a) flow rate, in gpm; (b) the head in ft; and ( c) the water horsepower, HP. Assume near-radial entry flow. a. flow rate Answer : ____________________ gpmb. head Answer : ____________________ ftc. water horsepower Answer : ____________________ HP
Section 5.1.4 Deforming Control Volume 5.30 (WILEY A hypodermic syringe (see Fig. P5.30) is used to apply a vaccine. If the plunger is moved forward at the steady rate of 20 mm/s and if vaccine leaks past the plunger at 0.1 of the volume flowrate out the needle opening, calculate the average velocity of the needle exit flow. The inside diameters of the syringe and the needle are 20 mm and 0.7 mm. Qleak Qout Figure P5.30
A centrifugal pump running at 3500 rpm pumps water at a rate of 0.01cu. m./sec. The water enters axially, and leaves the impeller at 5m/s relative to the blades, which are radial at the exit. If the pump requires 5kW, and is 67% efficient, estimate the basic dimensions (impeller exit diameter and width).
Q6) Calculate the hydraulic horsepower for pumping 500 gal / min from an inlet pressure of 5 psig to an outlet pressure of 30 psig (a) For water. (density 1000kg/m³) (b) For gasoline. (density 700 kg/m³) Discuss the difference for the pump power of (a) and (b) Q7) How many horsepowers are required to compress 20 lbmol/h of helium (k = 1.666) from 1 atm at 68°F to 10 atm using; (a) (b) (c) 68°F? An isothermal compressor? An adiabatic compressor? A two-stage, adiabatic compressor with optimum interstage pressure and intercooling to
The bottom quarter of a vertical cylindrical tank of total height 0.4 m and diameter is filled with a liquid (SG>1, like glycerin) and the ret with water. The tank is now rotated about its vertical axis at constant angular speed w. Determine the value of angular speed in rad/s when point P on the axis at the liquid-liquid interface touches the bottom of the tank. Include the free body diagram in your solution. a.12.1 b.10.3 c.14.4 d.13.2
An ideal water jet with volume flow rate of 0.05 m^ 3 / s strikes a flat plate placed normal to its path and exerts a force 1000 N Considering the density of water as 1000 kg / (m ^ 3) , find the diameter (in mm) of the water jet.
Using the performance curve of pump A given in Example VIc.3.2 (41.5” and 710 rpm) and find: a) total dynamic head of a similar pump (pump B), at peak efficiency, having a diameter of 35 inches. Assume that both pumps A and B are operating at the same speed. b) pump head if pump B is now operating at 1170 rpm. [Ans.: a) H = 192 ft and b) H = 521.5 ft].