5.1 Classify the following soil using the U.S. Department of Agriculture textural classi- fication chart. Particle-size distribution (6) Soll Sand Silt Clay A 20 20 60 в 55 5 40 45 35 20 D 50 15 35 E 70 15 15 VIce Buruen tetuea

Q: Sketch thefollowing figure ,orthographic view ( using catia )  Metion the top view side view and…

A: From figure.......

Q: Name the four principal applications of photography to construction documentation.

A: The following are the names of four principle application of photography to construction…

Q: Determine the coordinates of the centroid of the lines used as boundaries of the ea shown in Problem…

A:

Q: 35 aw the projections of this shape 25 20 20 A

A: GIVEN:   TO FIND: Draw the projection of the given shape.

Q: The six standard views in orthographic projection are front, top, bottom, and what?

A: Answer : Left view Right view  Rear view

Q: Construct the topview of this ortographic figure, and the isometric figure

A: Answer We can draw the Top view and Isometric view from the given orthographic figure using the…

Q: TOP VIEW 60 80 40 20 30 50 35 15 10 FRONT VIEW RIGHT SIDE VIEW

A:

Q: Law of Cosines (Engineering):

A: Law of cosines signifies the relation between the lengths of sides of a triangle with respect to the…

Q: continue dimension and baseline dimension?

A:

Q: 1. Which tools is to enlarge or reduce size of object? 2. Which tool is used to extend an object to…

A: Ans  1.Users can enlarge view by using scale command in AutoCAD. Users may enlarge & reduce the…

Q: Show Isometric View.

A: Answer  We can obtain the isometric view from given views in Autocad using the following steps 1)…

Q: Assignment 2.: A line CD, 60mm long, is perpendicular to VP and parallel to HP. It is 20 mm above…

A:

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A:

Q: Find centroid of figure from X axis

A:

Q: 99 # 日 P

A:

Q: What is the significance of Topcon's image?

A: The Significance and elaboration about topcon's image system is illustrated below.

Q: L (Isometric Drawing) J 56 104

A:

Q: Civil Engineering Orthographic and isometric projections are two basic types of graphic projection…

A: The statement Orthographic and isometric projections are two basic types of graphic projection is…

Q: What are the components of Hydrograph?

A: A hydrograph is defined as a graph that represents the relation between the flow rate or discharge…

Q: Level surface, Bubble line, Horizontal line, Level line, Line of collimation, Bench mark, Change…

A:

Q: Please solve question 3. An example has been given of a solved orthographic view. Given two…

A: We need to construct an Auxiliary view

Q: Draw the the 3 principal views and auxiliary view (like in the second photo)

A: Auxillary view: The orthographic view drawn taken according to the line of sight which is not…

Q: Q.3. Use Scale (1:1), for the front and side views shown draw the isometric projection: 50 30 R30 30…

A: To get the isometric projection from the given views. 1. Draw two lines perpendicular to each other…

Q: 60 mm 30 mm 30 mm 45 mm

A:

Q: Three lines were measured on a sloping grpund and each was equal to 200 meters. The vertical…

A:

Q: What of the following about the scale is/are false ?

A: The scale represents the ratio between the measurement drawn in a plan to the actual measurements.

Q: Q2: Draw front and side view projection for the following 36 12, 34

A: Given section: If you look at the given section from the front, the red coloured area will be…

Q: B Look to the Contour map above Solid line is the ground surface level Dashed line is Water table…

A: Contour lines are drawn on contour maps which represents the elevation or depression at any…

Q: What do you mean by specific collecting area in an ESP?

A: Solution: The specific collection area is basically the area of the gas of flue through the…

Q: Using multiview, the user can layout drawings in different paper sizes at the same time. O True…

A: A multi-view drawing is one that shows two or more two-dimensional views of a  three-dimensional…

Q: Explain oblique angle of projection

A: oblique angle of projection- it is a graphical projection with parallel line which is used to…

Q: 20 20 FRONT ELEVATION 60 20 60

A: For given isometric view following are top, front and side views are first angle projection views

Q: in engineering

A: Consider a rectangular section where X and y are placed in 2nd and 4th quadrant respectively.

Q: 1.what are the properties of text aside from its height?autocad 2. what other linetype do you know…

A: 1) We have two type of text available in Autocad Single line  Multiple line Some other Properties of…

Q: From the figure shown, determine the following: y L, L4 CE h, h7 he h2 hs he he Distance of the…

A: To determine Distance of Centroid from x-axis.

Q: Explain 1st and 3rd angle of projection

A: First angle projection and Third angle projection are two different methods of creating a 2D drawing…

Q: Exercise 1.5: Third Angle Projection type is displayed. Estimate the dimensions. Draw the Visible…

A: To draw the right side view of the given figure.

Q: Q1. DRAW THE ORTHOGRAPHIC PROJECTION VIEW OF GIVEN OBJECT BELOW. ELEVATION PLAN SIDE VIEW

A: Instructions :  To draw the orthographic projection view ( First angle method ) consider the…

Q: Exercise 1.6: Estimate the dimensions. Draw the Front view, Top view and Right view. Draw the…

A: Question related to the engineering drawingsmodel is given  FINDFront viewtop viewright…

Q: Given the following isometric drawing, how many edges are drawn as points in the right side view of…

A: ASKED: To determine the number of edges of the given isometric drawing that are drawn as points in…

Q: Y 266.67 mm 133.33 mm 100.00 mm 300.00 mm 100.00 mm 150.00 mm 00 mm 100 mm 75 mmi 200 mm

A: