5. Use the assumption that there is a complete mixing of the two inflows before the discharge. Determine a. Mass flow rate b. Velocity at discharge c. Specific gravity of the mixture at the discharge

Q: Von mises and tresca agree in pure shear

A: In machine design, mainly five failure theories are used to relate stress with the strength of…

Q: Why do the Ductile materials fail in shear?

A: Ductile materials are the materials which goes plastic deformation before the fracture. When any…

Q: Name different failure theories used in machine design. Explain any two in detail considering…

A: To name: The different failure theories used in machine design, explain any two in detail…

Q: State the formula for: - the actual mechanical advantage (AMA) of wedge; - the ideal mechanical…

A:

Q: Do ductile materials fail in shear?

A: The type of materials that undergo considerable plastic deformation before fracture are known as…

Q: Draw an approximate mechanical frame of skeleton, modeling with levers and

A:

Q: Table 3 shows the fatigue data for a ductile cast iron to be used for an automobile axle that…

A: Given Data for ductile Cast iron Stress Ampitude (Mpa) Cycles to failure 740 1*101 604.8…

Q: What to do if the simulation result in Fusion 360 shows this (Screenshot attached)  Please provide…

A: Each thing has a stress limit that is determined by the material used in construction. A crucial…

Q: In a forming process the diameter of the specimen is 1 cm and its length changes from 50 mm to 60…

A:

Q: 9) A long thin wire suspended from a fixed point is subjected to a load which cannot cause the…

A:

Q: please make an ilustration relating pressure to area and force, it can be an example drawing

A: To make: An illustration relating pressure to area and force. Explanation: Consider an image below:…

Q: Why should the thermal stresses be considered in design?

A: The stresses generated due to rapid heating or cooling of the structure are known as thermal…

Q: raw a potential to failure curve and explain its characteristics

A:

Q: (a) Manufacturing is “ the transformation of materials into items of greater value by means of one…

A: Manufacturing can be defined as the bulk production of any useful item from the raw materials using…

Q: How can machinery parts and pipeline welds be tested for flaws without destroying them? Name several…

A: We can inspect or test the welded parts and pipe line welds for flaws without destroying them…

Q: For each of the following parts for an overhead crane; Bridge, end carriage, wheel, shaft and…

A: Function: The bridge is the main structure of the crane that spans the width of the workspace. It…

Q: How the forced vibrations can arise?

A: When a body vibrates due to the influence of external periodic force, then this type of vibrations…

Q: Q3: What is the magnitude of true strain (e) if the true stress (o) is 15% larger than engineering…

A: Given data:- True stress=1.15×Engineering stress To find:- Magnitude of true strain

Q: A compression test is performed on a 2” diameter by 5” long bar of an unknown metal.  At the end of…

A: Given:d1=2 inl1=5 inl2=3.5 inK=250 MPan=0.4a)Volume before compression=volume after compression…

Q: Q1a) A sample of an aluminum alloy has a tensile strength of 275 MPa, What will be the  maximum…

A: Tensile strength, is the maximum load that a material can support without fracture when being…

Q: (a) A teacher, design supervisor, examining a design of a student, point out to him that the shaft…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: What is the difference between material & a structure?

A:

Q: Water flows through the curved pipe shown in the figure below where point X denotes the center of…

A: Let the inlet to the curved pipe be denoted as section 1 and the exit be denoted as section 2. Write…

Q: b) The elastic limit for some materials is difficult to determine exactly and so a yield point is…

A: Step 1: Step 2: Step 3: Step 4:

Q: Describe the concepts behind principal components and dimensionality reduction.

A: given; Describe the concepts behind principal components and dimensionality reduction.

Q: Explain in your own words how the stress test (performance test) is applied to the patient turning…

A: Medical equipment to find test performance

Q: al cup of equired to pach job f 240 cc ecificatio

A: Given: The radius of hemispherical cup is 15cm The force required to deform is 8KN. The approach…

Q: Q.Define the slip and show the effect of slip on velocity ratio.

A: SLIP Pulleys (driver/driven) and the band are defined as inadequate frictional grip. Slip is the…

Q: When does stress concentrations become important?

A: Stress concentration is very important in the case of cyclic loading. stress concentration leads to…

Q: a pipe varies jointly with the internal pressure and the diameter of the pipe, and inversely with…

A: Given data as per question The stressσ in pipe varies jointly with the internal pressure(P) and the…

Q: Describe distributed loadings?

A: Distributed load is a load applied across a length or area instead of at one point on a beam. If we…

Q: Why is it important to make standards for the different building/engineering materials? (Tensile…

A: All things considered, we've been building two-stories wooden homes for millenia, so what's the…

Q: As an engineer you are asked to choose 1 component from what you studied ( Screw, rolling bearing,…

A: From the above components, I am going to choose the 'key' components. A basic element on which force…

Q: d. List in order the various phases for the general procedure of design process e. Define the terms…

A: The six steps involved in the process of new product design are : 1. Idea Generation: The design…

Q: How does material, function, shape and process relate with each other?

A: When ever we talk about the product experience, the first thing hits most Is the material of the…

Q: Explain the term degree of indeterminacy? Give an example?

A: Indeterminacy is defined as the difference between the internal forces and the number of…

Q: The new line of go-karts will have a two-stroke internal combustion engine. The engine generates 35…

A: Given: Power = 35 hp = 26.0995 kW Mean speed = 2000 rpm To find: Design a flywheel