5. The pitch circle diameter of the smaller of the two spur wheels which mesh externally and have involute teeth is 100 mm. The number of teeth are 16 and 32. The pressure angle is 20° and the addendum is 0.32 of the circular pitch. Find the length of the path of contact of the pair of teeth

Q: In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc=392…

A:

Q: The drawing represents a planetary reduction gear used in aeronautics. Calculate the speed of the…

A: Speed of motor: N3=1200 rpm and considering N1=0 (is fixed) Number of teeth: Z1=50 teethZ2=18…

Q: The horsepower input of the power screw. The efficiency if the weight loaded is 10 kN.

A: This is consisting of Two threads twisted together in which the pitch is equal to twice the distance…

Q: The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker…

A:

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

A:

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: Sun gear-'2' rotates at 500 rpm and arm '6' rotates at 750 rpm both in clockwise AS viewed from…

A: Given: The speed of sun gear 2, N2 = 500 rpm(CW) The speed of arm, x = 750 rpm (CW)

Q: Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and…

A: The diameter of the smallest pulley = 2 in. Thus the maximum speed will be maximum at this pulley.…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: at distances of 100 mm from the central plane of the middle eccentric, find the amount of he masses…

A:

Q: 4- The airplane, traveling at a constant speed of 50 m/s, is executing a horizontal turn. If the…

A:

Q: 8.10 Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in…

A: Given: Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed (N)=750rpm Power=4.6kW…

Q: FOR FIG REFER ATTACHED FILE The shaft is massless. A thin attached triangular mass ‘m’ is mounted…

A: Given, Mass of the triangular lamina - m kg Rotational speed of the shaft - ω rad/s

Q: Draw schematic figures and find max./min. diametrical slip / press mouth for the following four…

A: This problem is Hole Basis system. Here there are three types of fit. 1. Clearance Fit : shaft size…

Q: The center O of the gear shown in (Figure 1) is moving with a speed of vo=3 m/s. The gear rack B is…

A: Given: The center of the gear shown in (Figure 1) is moving with a speed of vo = 3 m/s. The gear…

Q: Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in mesh.…

A: According to the given data Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed…

Q: Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass…

A: Given: The mass of bar, m = 50 g The angle, θ = 15° The angular acceleration of bar, α’ = 20 rda/s^2

Q: The Smm module with 40 number of teeth gear is used to transmit 42.3 kw power at 350 rpm .Find the…

A:

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

A:

Q: nism when annulus is i

A: introduction: we have to find out degree of freedom

Q: is the wheel provided with a series of backward curved vanes. Select one: O a. Spiral casing O b.…

A: The centrifugal pumps are made up of many components like the suction pipe, delivery pipe, casing,…

Q: 1-)The diagram of the change of cutting force for the cutting work performed with the press seen in…

A: Given data   Engine revolution =  900 rpm Flywheel revolutions = 60 rpm. Themoment of inertia of…

Q: belt is on the steps either side of the center step. If the minimum speed is 40 rpm and the smallest…

A:

Q: Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal…

A:

Q: Find the chordal tooth thickness and chordal height at constant chord for a gear that has number of…

A: The contact always accurs at at two fixed point A and B hence AB=constant chordfrom the…

Q: A torque T = 0.30 N-m is applied to a bevel gear B. Bevel gear D meshes with gear B and drives pump…

A:

Q: 2.5" 30.375" s 18.75" 4.25 26" 2.5" Espring FBY Fax 7 Analyze the forces acting on the clutch fork…

A: The force analysis can be done by using the equilibrium equation on anybody. The Shaft has lots of…

Q: In the image on the right, there is a red gear G1 on the left with a radius of r1 = 2.81cm. Gear G1…

A:

Q: Each of two gears in a mesh has 60 teeth and a module of 6 mm. The teeth are of involute profile.…

A: Data given-  T = 60  m = 6 mm  Arc of contact = 2.5 × circular pitch

Q: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

A: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

Q: Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a…

A:

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: Find the value of the input torque on the crank-shaft mechanism in followin Figure. The centers of…

A: To carry out dynamic force analysis of the four-bar mechanism shown in the figure, it is required to…

Q: H, = 0.40 Hx = 0.30 D 150 mm 150 mm B E 300 mm 300 mm \F 150 mm 150 mm 250 mm

A:

Q: The diagram below shows a shaft with spur gear (B), bevel gear(D), and two supporting bearings (A…

A: Given : The radius is The pressure angle  for the spur gear is The pressure angle of bevel gear at D…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.