5.Suppose we have the instruction Load 1000. Given memory and register R1 contain thevalues below:Memory0x10000x11000x12000x1300Mode0x1400ImmediateDirectIndirectIndexed0x4000x10000x11000x1400and assuming R1 is implied in the indexed addressing mode, determine the actual value loadedinto the accumulator and fill in the table below:0x1300R10x200Value Loadedinto AC

5. Suppose we have the instruction Load 1000. Given memory and register R1 contain the values below: Memory 0x1000 0x1100 0x1200 0x1300 Mode 0x1400 Immediate Direct Indirect Indexed 0x400 0x1000 0x1100 0x1400 0x1300 and assuming R1 is implied in the indexed addressing mode, determine the actual value loaded into the accumulator and fill in the table below: R1 0x200 Value Loaded into AC

5. Suppose we have the instruction Load 1000. Given memory and register R1 contain the values below: Memory 0x1000 0x1100 0x1200 0x1300 Mode 0x1400 Immediate Direct Indirect Indexed 0x400 0x1000 0x1100 0x1400 0x1300 and assuming R1 is implied in the indexed addressing mode, determine the actual value loaded into the accumulator and fill in the table below: R1 0x200 Value Loaded into AC

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

An 'instruction fetch/read' results in three sets of numbers that go to the Registers Block as studied in class. These three numbers in the instruction represent bits 25-21 for 'Read Register 1', bits 20-16 for 'Read Register 2', and bits 15-11 for the 'Write Register'. What does the 5 bits width of each of these indicate? a. That the word is 15 bits long in this architecture b. That each word is 32 bits long c. That there are 32 registers that can be addressed in this architecture d. That there are 15 registers that can be addressed in this architecture
Problem 6 Assume that the instruction MOV EAX,[EBX+4*ECX] is to be encoded by a Pentium processor operating in the 16 bit instruction mode. Express the instruction in machine code (Hex). ΒΥΤΕ ΒΥΤΕ ΒΥΤΕ BYTE ΒΥΤΕ ΒYΤΕ ΒΥΤΕ 3 4 5. 6. ADDRESS REGISTER SIZE - OPCODE D MOD REG RM SCALE LOW HIGH LOW HIGH SIZE - 67H 66H or SEGM OVERRIDE PREFIX (3 bits) DATA (6 bits) (2 bits) (3 bits) D INDEX ΒΥΤΕ DISP/ DATA DISP/ DATA DATA
2. Consider the following instruction: beq $t0, $t1, 0xA010 What are the values of Control signals generated by the MIPS architecture to execute this instruction. Show with a chart and explain it all clearly. (You may draw a simplified datapath flow)
3. For each instruction in the table, write 8 hexadecimal digits that represent the 32 bits in the destination register after the instruction is executed. Assume s0 is 0x98AB3C6A, s1 is 0x20503666. Instructions to, 50, s1 t1, so, s1 t2, so, s1 t3, 50, 51 addi t4, 50, 0x210 wwwwwww andi t5, 50, -16 add and or xor slli t6, 50, 12 srai s2, 50, 8 Dest. reg. in 8 hexadecimal digits
For the given x86-64 instruction, list the following for each operand: • location of operand (register, memory, or immediate) • size of the operand in bytes • addressing mode of the operand 9. addq $5, %rax 10. subw -8(%sp), %cx 11. movl (%esi), %edx 12. movb %cl, 8(%esp) 13. addw 6(%ebx, %eax, 4), %si
Question 1: Use Indirect addressing to write a PIC24 assembly code that complements and adds 5 and multiply by 2 to 1024 data bytes into the memory at starting address 0x1000. The original data are stored in the memory starting from address 0x800.
1. Translate the following instructions so each can be directly executed by vertical architecture without using and additional registers. a. TIR := NOT(AMASK) + AC; Goto 65 b. A:= B + C + NOT(A); If Z goto 15 2.Show the hexadecimal value for OP, R1 and R2 for each instruction you come up with for part a and b in the above question.
Please explain the difference between Register Direct Addressing and Register Indirect Addressing with proper examples. Please find the Machine code for the instruction: Mov 101A[BP+DI] , DL . Consider the Opcode fora Mov operation to be 10 00 10
The NOR instruction is not part of the RISC-V instruction set because the samefunctionality can be implemented using existing instructions. Write a short assembly codesnippet that has the following functionality: s3 = s4 NOR s5. Use as few instructions aspossible. Write RISC-V assembly code for placing the following immediate constants inregister s7. Use a minimum number of instructions.a) 59b) -199c) 0xDDCBE289d) 0x11236BDF
Match segment and offsetregisters and determine their correspondingactual memory location addressed of the following real mode 80286 segment registers given below. Segment Register Effective Address 1. CS = 2010H 2. DS = 2100OH 3. ES = AB80H 4. SS = 1234H 5. DS = B20FH When: a. DI = 2000H d. IP = ABCDH b. BX = 100AH e. BP = 12FFH c. SP = 3A00H Type the address in uppercase. Do not forget to append H to each addresses. 1. EA: 2. EA: 3. EA: 4. EA:
Consider a 16-bit processor in which the following appears in the main memory, starting at location 200.a. The first part of the first word (content at 200) indicates that this instruction loads a value into an accumulator; the value of 300 in location 201 may be part of the address calculator. The mode field specifies an addressing mode and, if appropriate, indicates a source register. a. Assume that when used, the source register R1, which has a value of 500. b. There is also a base register that contains the value 100, Assume that location 249 contains the value 399, location 250 contains the value 400, and so on. Determine the effective address and the operand to be loaded for the following address modes:
What will be the values stored in registers r1 and r0 after the execution of the instruction mul r16, r17 if r16 and r17 originally contain the following values? (a) 0x58 and 0x37 (b) 0x29 and 0x49