5. In lab, you need to prepare at least 100 mL of each of the following solutions. Explain how you would proceed using the given information. Like a lab manual, your answer should provide instructions in complete sentences, indicating specific masses, volumes, glassware, and equipment to be used. Your available chemicals include KCl(s), NAOH(s), C,H12O6(s), H2O(1), and CH;OH(1). a. 2.0 m KCl in water (density of H2O = 1.00 g/cm') b. 15% NaOH by mass in water (d = 1.00 g/cm') c. 25% NaOH by mass in CH3OH (d=0.79 g/cm') d. 0.10 mole fraction of C,H12O6 in water (d=1.00 g/cm')

5. In lab, you need to prepare at least 100 mL of each of the following solutions. Explain how you would proceed using the given information. Like a lab manual, your answer should provide instructions in complete sentences, indicating specific masses, volumes, glassware, and equipment to be used. Your available chemicals include KCl(s), NAOH(s), C,H12O6(s), H2O(1), and CH;OH(1). a. 2.0 m KCl in water (density of H2O = 1.00 g/cm') b. 15% NaOH by mass in water (d = 1.00 g/cm') c. 25% NaOH by mass in CH3OH (d=0.79 g/cm') d. 0.10 mole fraction of C,H12O6 in water (d=1.00 g/cm')

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Two solutions are combined: 600 mL of 147 mM (NH4)2CO3 and 541 mL of 159.17 mM Fe(NO3)3. What is the concentration of the ammonium ion in solution after the reaction is complete? Report your answer in mM.
The maximum contaminant level of cyanide (CN) in drinking water as set by the the Environmental Protection Agency (EPA) is 0.00020 g · L. Express this concentration in parts per million (ppm). Assume the density of water is 1.00 g/mL. concentration: Ppm
4) Write a chemical equation describing the dissolution of Ba(NO3)2 in water. To give you an example of what I'm looking for, for NaBr, the equation would be NaBr(s) → Na*(aq) + Br- (aq). 5) Based on your equation from question 4, if 41.9 g of Ba(NO3)2 are dissolved in water to produce a total solution volume of 495 mL, determine the molarity of NO3- in the solution?
A 0.150 M sodium chloride solution is referred to as a physiological saline solution because it has the same concentration of salts as normal human blood. Describe the step-by-step procedure on how to prepare 450.0 mL of a physiological saline solution.
Lead is a possible contaminant in public water systems. There are many reasons we should be concerned about this, but this may be especially concerning if the water is used for drinking. Removing all lead is not feasible, so many local governments must set an “acceptable” concentration for contaminants. The “acceptable” concentration of lead in public water for some states is 7.2 x 10^-7 M. If 10.00 mL of 1.00 M lead is poured down the sink, how many liters of water are required to make sure the concentration of lead is 7.1 x 10^-7 M, which is just below the acceptable level?
The stock solution in the stock beaker contains 10.00 mL of 0.1000 M iron(III) nitrate solution, 10.00 mL of 0.1000 M potassium thiocyanate solution, and 10.00 mL of 0.5000 M nitric acid solution. What is the total volume of the stock solution? How many moles of iron (III) nitrate are present in the stock solution? How many moles of potassium thiocyanate are present in the stock solution? Based on the moles of iron (III) nitrate and moles of potassium thiocyanate, how many moles of iron (III) thiocyanate do you expect to be formed Once you determine the moles of iron (III) thiocyanate formed, determine the concentration of iron (III) thiocyanate in the final solution.
Calcium nitrate (Ca(NO3)2 ; MM =164.0878 g/mol)) dissolves in cold water to the extent of 266 g per 100. mL. What is the concentration (mol/L) of nitrate ions in this solution? Ca(NO3)2 -> Ca+2 + 2 NO3-
A solution is made by dissolving 25 g of NaCl in enough water to make 1.00 L of solution. Assume that the density is 1.00 g/cm^3.
Imagine you are preparing a solution of NaCl and a solution of CaCl2. After you prepare them you go out to lunch with your colleagues. When you come back you cannot remember which solution is in which container because you forgot to label the containers before going to lunch. What experiments can you perform to identify each solution?
Briefly and concisely explain how you would prepare 250. mL of a 0.100 M copper (II) sulfate solution if you have at your disposal solid copper (II) sulfate, a balance scale, distilled water, a beaker, a volumetric pipet and pump, and a 500. mL volumetric flask. Be sure to provide the exact amount of solid required and discuss the specific steps you would perform in the lab in preparing your solution.
Commercial bleaches typically rely on sodium hypochlorite, NaClO, as the active ingredient. The molarity of a strong commercial bleach solution is 1.12 M. It is recommended that for household sanitizing that you put 10 mL of bleach per liter of water. What is the concentration of the diluted solution? Show your work.
What volume (in mL) of a 2.60 M solution of CH₂OH must you add to a 1.00 L volumetric flask so that adding water to the mark will create a 0.150 M solution?