5. Draw a diagonal scale 1:1000 to show 1.5 meter. Show a distance of 25.5 meters on it.

Q: 11-13. The timber beam has a width of 6 in. Determine its height h so that it simultaneously reaches…

A:

Q: Additional Problem #2 30 mm Locate the centroid of the cross-sectional area at right. Sketch the…

A: The given figure is shown below:

Q: Locate the centroid of the plate area shown below: (All units are in mm). Ø200- Ø150 300 300 Ø50 50…

A:

Q: area of the cross section.

A: Given:- formation width=18m depth of cut at midpoint of formation=3m transverse slope on right side…

Q: create (P,L,E,A,N,U,G) 2D drawing using lines, circles, curves,etc

A: Here is your drawing

Q: The ABC rod is supported from point B and is in equilibrium with a force F1 = 12KN applied from…

A: Given Data: The equilibrium force F1 is, F1=12 kN The shear strength at pin B is, τs=350 MPa The…

Q: 4. An object in isometric view is given as in Figure 3. Draw the object in Third Angle Projection at…

A: An isometric view is given. We need to draw top view, front view and side view

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A: Top View of the given object is as shown below.

Q: REQUIRED: ISOMETRIC DRAWING VEN FIGURE SHOWN TOP VIEW syooing 0.5cm FRONT VIEW RIGHT SIDE VIEW 45

A:

Q: Given the multiview set of the cut block objects shown, use isometric grid paper to sketch an…

A:

Q: top wiew Units are in millimeter right side 40 IS 35 ーネィー ー子ィー front viw 1-..

A: Given orthographic views- Top view Front view Right side view

Q: Draw the full sectional front view, as well as draw the top view and side view of the object as…

A: The Section A-A Front View diagram of the given object is as shown below (not to scale):

Q: Using a convenient scale, manually plot the following technical descriptions. Label your sketch…

A: Given : technical description

Q: 0.35m 0.35 LOS 105m

A:

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: Write a short note on:  Aligned dimensioning. Unidirectional dimensioning.

A: In this system of dimensioning, the dimensions are written along the same direction in the entire…

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 22 19 38 Ф 18 22…

A: Given Data :

Q: can you show the sides with dimensioning

A: To show the sides with dimensioning

Q: 90 80 70 703 E.60 E50 40 E 40 30 E20 10 ) simple vertical staff gauge.

A: A staff gauge is used to measure water surface elevation or any another surface elevation.

Q: Compute an actual dimension of a distance if the given drawing measurement in the plan is 28 cm…

A: Map scale  A distance on a map and its corresponding distance on the planet are related by a scale.…

Q: (Figure 14.38) a. Draw a true-size view of planes AOC and DLN. b. Find the area of the largest…

A: The inclined angle is measured by proper techniques and formula and accurate calculation. The true…

Q: Draw the figure to an enlarged scale in Isohyetal method

A: The iisohyetal approach is a technique for calculating the average amount of precipitation within a…

Q: SIZE : 300 mm. x 300 mm. MAIN BARS: 8-20 MM.Ø BARS. TIES: 3 TIES AT 10 MM. Ø 3 @ 50,5 @ 100, 7 @ 150…

A: The details are mentioned on the figure and spacing between ties are explained below.

Q: Construct a diagonal scale and show on it a distance of 1.12 inche

A: Diagonal scale is an engineering measuring instrument that is combined with a set of parallel…

Q: Sketch an ISOMETRIC DRAWING from the attached orthographic projection. Follow the assigned…

A:

Q: Draw a diagonal scale 20mm: 1m up to 8m and indicate 6.74m

A:

Q: Q) Draw the following with scale 2:1: 1. Front Sectional View on A-A 2. Side View 3. Top Sectional…

A:

Q: Calculate the vertical index difference and vertical angle in Tab

A: Station Target Vertical position Vertical dial reading O A L 78o32'12'' R 281o27'54'' B L…

Q: 40 15 60 90 10 45 07 30

A: The Top view is:

Q: 54 80

A: Given  Draw the corresponding perspective sketch.

Q: Derive the Trapezoidal rule for multiple segments. Also show a graphical sketch.

A:

Q: Detail drawing is a multiview representation of a single part with dimensions and notes. Select one:…

A: Detail drawing conveys the information and instructions for manufacturing the part. Hence Detail…