10. Which of the following is correct in dimensioning a drawing?

Q: A small metal bar, whose initial temperature is 20°C, is dropped into a container of boiling water.…

A:

Q: Show the dimensions of the object on its orthographic views.

A: The orthographic views of the object using the third angle projection are as shown along with their…

Q: Use the cutting planes shown to draw the sectional views.

A: The sectional view of the above figure or diagram is shown in the below step :

Q: LENGTH SI DE BEARING (m) 382.50 Due East AB вс 248.78 Unknown S89°25'E s27 45'w CD DE 220.42 Unknown…

A:

Q: Explain the difference between 1:50 and 1:100 in scale ruler Sketch it please to fully understand…

A: In architecture and civil drawings, different scale measurements are used in order to transfer the…

Q: Calculate the member forces of the loaded structure. y 60 kN D 40 kN 7 m C, 3 m Ax Ay -4 m-

A:

Q: Additional Problem #2 30 mm Locate the centroid of the cross-sectional area at right. Sketch the…

A: The given figure is shown below:

Q: Locate the centroid of the plate area shown below: (All units are in mm). Ø200- Ø150 300 300 Ø50 50…

A:

Q: List the four distinct kinds of drawings according to their projection methodologies.

A:

Q: Just draw the figure, if possible

A: Given data in question  Forward bearing  Back bearing Line Closed traverse To find out  Draw diagram…

Q: Draw the orthographic views of the object shown.

A: Orthographic Projection: It is the most common method which represents three-dimensional objects. It…

Q: what lines should be drawn first when finished-line quality is being used

A: Brief concept- These given things are related to the drawing.

Q: Given the Isometric View, draw the following: Top View Front View Right Side View Section View…

A: (Disclaimer: Since you have posted a question with multiple sub-parts, we will solve first three…

Q: 12. The ability to magnify details in a drawing or reduce the drawing to see it in its entirety is a…

A: Generally in AUTOCAD zooming can be directly done by using keyboard shortcuts like using the “+” key…

Q: SM Ø HOLES 10M A12.5M "SM 125M BOM FRONT VIEW SIDE VIEW

A:

Q: What is the importance of drawing the orthographic view of an object?

A: Sometimes 3-D drawings  can be used to show the overall design and concept but not often clear or…

Q: why were the dimensions changed in the drawing

A:

Q: A U-tube differential manometer connects two pressure tubes A and B. Pipe A contains carbon…

A: 1. Pressure in Pipe A () = 120 kPa2. Specific gravity of carbon tetrachloride in Pipe A () = 1.63.…

Q: Name any four shape that you can identify from the sketch

A: Any sketch such as still life, landscape etc. is prepared with the helps of basics shapes. These…

Q: 1. The radius of a simple curve is twice its tangent distance, if the degree of curve is 4°. a) What…

A: This problem is related to Simple Curve from Surveying Engineering. In this question, Given a simpe…

Q: If a standard view in a drawing has hidden lines, then creating a sectional view is always…

A: Sectional view represents the internal configuration of any object. It shows the details of all…

Q: Given the following isometric drawing, draw the top view, front view, and right side view

A:

Q: Does the solution for part a really end once the sketch for the tied column is drawn. Dont you have…

A: Yes, the solution part is completed once the dimension and reinforcemnets are computed and drawn.…

Q: top wiew Units are in millimeter right side 40 IS 35 ーネィー ー子ィー front viw 1-..

A: Given orthographic views- Top view Front view Right side view

Q: Answer g  Draw correct and complete figure

A:

Q: 1. Although you have not seen this type of table before, you should be able to work through the…

A: Given data : Materials and their properties Material  Cost (£/kg) Density (kg/m3) Yield…

Q: Part b) A 25-mm-diameter shaft is pulled through a cylindrical bearing as shown in the figure below.…

A: v = 3m/s h (gap) = 0.3mm

Q: The value of the smallest division on the main scale of a horizontal circle is graduated to 1/3…

A:

Q: Create a hand drawing of the isometric view of this object to scale.

A: First Draw one missing view from the given two view by projecting lines.  A. After getting the…

Q: Using a convenient scale, manually plot the following technical descriptions. Label your sketch…

A: Given : technical description

Q: 0.35m 0.35 LOS 105m

A:

Q: Instructions: Draw the three basic orthographic projections of the figure. (Top View, Front View,…

A: Hand made drawing are attached herewith of different views. Which will give you idea about different…

Q: Correctly Dimension the object using datum dimensioning

A: To show the datum referencing of the drawing

Q: What finished surfaces are available when selecting chalkboards?

A: The finish surfaces is based on material or paint we used for surfacing. there are certain options…

Q: (D) -

A: A sectional view in engineering drawing is a representation of an object as if it were cut by an…

Q: Q3: In a catchment area, approximated by a rectangular of coordinates (50, 0), (100, 50), (50, 100),…

A:

Q: Top, Front and Side view of this sketch.

A:

Q: Draw the isometric view for the given figure.

A: Isometric view:- In engineering and technical drawings, isometric projection is a method for…

Q: PART 1. AREA & VOLUME OF PRISMS Draw the indicated views for the isometric drawing below. Isometric…

A: An isometric view is given, we need to draw: 1. Top view 2. Left view 3. Front view

Q: Construct a diagonal scale and show on it a distance of 1.12 inche

A: Diagonal scale is an engineering measuring instrument that is combined with a set of parallel…

Q: Two identical trusses support a load of 100 N as shown in the figure. The length of each truss is…

A: Given Load 100 NLength 1 mCross section 200 mm2Elasticity modulus 200 GPaTo find out Force in member…