5. Design a channel carrying a discharge of Q cumec with critical velocity ratio and Manning's roughness value equal to 1.2 and 0.0225 respectively. Assume the bed slope equal to 1:6000. Use Kennedy's approach for design. Side slope of channel is 1H: 2V.

Q: Use Kirschmer's equation_to find the head loss through a rectangular bar screen used in treatment…

A: For computation of rack losses or head loss through a rectangular bar section ,we have  O.…

Q: In a circular channel 2.5meters in diameter, flowing below half full, the water surface width is…

A:

Q: Water flows over a smooth submerged object in a channel of width 1.2 m. The water depth upstream of…

A:

Q: An earthen channel with a based 3 m wide and side slopes 1:1 carries water with a depth of 1m. The…

A:

Q: In 1957 H. Görtler proposed the adverse gradient test cases U =- U. (1 + x/L)" and computed…

A: Given Data: Stream velocity n=1 xsep/L=0.159 θ0=0

Q: A rectangular channel 4.0 m wide is laid a bed slope of 0.0008. A discharge of 15.0 m₽/ flows in the…

A:

Q: No..... Q4 A sketch of a transformed flow net in x-direction under a dam is shown in Figure, the…

A: Solution Given data Nf=3Nd=10kx=4×10-8ft/secky=1×10-8ft/seck=4×10-81×10-8=2×10-8 ft/secHead,…

Q: A. Design a trapezoidal channel to carry a discharge of 10.5 m^3/s. The bottom slop of the channel…

A:

Q: Question 11 of 23 A discharge of 1.2 m3/s flows on an open channel with a slope of 0.0062. If the…

A: Given data in question  Discharge  Bed slope Coefficient of roughness  Optimum triangular channel To…

Q: A concrete pipe culvert is to be constructed under road to carry a maximum discharge 9 m3 /sec. If…

A: When a pipe is fixed in an excavated trench to move water away called a pipe culvert. It is the most…

Q: Water flows in a 5-ft-wide rectangular channel with a flowrate of Q = 30 ft³/s and an upstream depth…

A:

Q: In the model test of a spillway the discharge and velocity of flow over the model were 2 m/s and 1.5…

A: given data Vm=1.5m/s Qm=2m3/s LpLm=36 Lr=136

Q: Ex. A small stream has a cross section which can be approximated by a trapezoid. The cross-sectional…

A:

Q: A trapezoidal is shown below. The particulars of the channel are as such: • Side slopes are 1 in 0.5…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: a. A rectangular channel is 4 m wide and has a longitudinal slope of 0.002. The channel is poured…

A: Given Data : Width of rectangular channel = 4m  longitudinal slope = 0.002 discharge = 25 m3/s Table…

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.