5. Car doors are easy to slam shut but difficult to press shut by hand force. The door lock as two latches, the first easily engaged, and the second requiring the rubber seal around the door to be quite compressed before it can engage. The rubber seal gives a spring constant of 50,000N/m at the lock position for the door, and the mass moment of inertia for the door around its hinges is 2.5kg- m². The distance between the lock and the hinges is Im. Calculate what force is needed to press the car door shut at the lock if a speed of 0.8m/s at the lock slams it shut.

5. Car doors are easy to slam shut but difficult to press shut by hand force. The door lock as two latches, the first easily engaged, and the second requiring the rubber seal around the door to be quite compressed before it can engage. The rubber seal gives a spring constant of 50,000N/m at the lock position for the door, and the mass moment of inertia for the door around its hinges is 2.5kg- m². The distance between the lock and the hinges is Im. Calculate what force is needed to press the car door shut at the lock if a speed of 0.8m/s at the lock slams it shut.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A student sits on a freely rotating stool holding two dumbbells, each of mass 2.97 kg (see figure below). When his arms are extended horizontally (Figure a), the dumbbells are 1.09 m from the axis of rotation and the student rotates with an angular speed of 0.749 rad/s. The moment of inertia of the student plus stool is 2.57 kg. m² and is assumed to be constant. The student pulls the dumbbells inward horizontally to a position 0.305 m from the rotation axis (Figure b). Wf Wi a 30€ 30€ = b (a) Find the new angular speed of the student. rad/s (b) Find the kinetic energy of the rotating system before and after he pulls the dumbbells inward. K before J J after
Solution for A weight W = 500 KN rests on the weightless and friction less bar AB. The cable connecting W and point B passes over a frictionless pulleys. Find the Reaction (Ra) at point A.
A board sits in equilibrium. On the left end, there is a wire that supports the board from the ceiling, and to the right, there is a sawhorse that supports the board from the ground. The sawhorse is a distance d= 1/5l from the right edge of the board. There is a block with mass ms= 4.5kg that is a distance 3/4l from the right edge of the board. Finally the board has a mass mb= 11kg. c) Write down Newton's 2nd law. Put the equation in terms of mb, ms, g, T, and Fn. Where T is the tension in the wire, and Fn is the normal force of the sawhorse on the board. d) Write down Newton's 2nd Law for rotations. Put the equation in terms of l, mb, ms, g, T, and Fn.
The lid shown has a mass, m = 60 kg, and is held in position by rod AB. The rod is held in place by rounded surfaces at A and B, where B is right at the edge of the lid. The hinges at C and D rotate smoothly and only the hinge at C provides a reaction force along its axis (the x-direction). a = 950 mm, b = 300 mm, c = 55 degrees Determine A) Reactions at hinge C and D B) Reaction force in rod AB C) The minimum coefficient of friction that is needed between the rod and the lid to maintain this position
SECW OM A motorbike wheel with an 8 kg mass has a 0.4 m radius of gyration around the z-axis, as shown in Figure. The wheel's shaft is supported by bearings A and B and rotates at a constant rate of 150 rpm in a counter-clockwise direction from the z-axis, while the frame rotates at 12 rpm in a counter- clockwise direction from the y-axis. Determine the resultant reaction forces at each bearing A and B due to the mass and gyroscopic effects. With the result of forces, which bearing has a tendency to fail first, which bearing should be considered for design purposes and explain the effect on motor if the bearing fail. y 0.55 0.4 All dimensions in meter (m)
4
Find reactions of R1 and R2 10 KN/m 8 KW/m 1a KN /m R2 1.5 m 4 m 3 m 1.5 m
Mechanism design
I just need the last problem at the bottom of the picture. When I submit the last problem by itself my question gets rejected because the value of the mass is required so I assume that you are supposed to refer to the previous problems to see that M=100Nm.
Six masses m1, m2, m3, m4, mM and mL, shown in figure below are to be completely balanced. The masses are : m1= 20.11 kg, m2 = 2 kg, m3 = 3 kg, m4= 6.3 kg, mM = 10.23 kg. The radii are : r1 = 0.1m, r2 = 0.12 m, r3 = 0.14 m, r4 = 0.12 m, rM = 0.1 m, rL = 0.5 m. The angles shown in the figure are: θ1 = 12º, θ2 = 103º, θ3 = 135º, Φ = 32º. The distances between different planes , shown in the figure are as follow: l1 =0.8 m, l2 = 0.7 m, l3 = 2.44 m. we need to find lm, l4 , mL and the angle α
A window cleaner is pulling himself up to a pulley that consists of two disks welded together as shown. The person is currently pulling straight down on the rope in his hands with a force of magnitude 580.4 N. The other rope is also vertical and is attached to the person's center of mass. The person's mass is 74.2 kg, the pulley's total moment of inertia is 395 kgm2, the radius of the small disk is 0.39 m, and the radius of the big disk is 0.73 m.What is the magnitude of the acceleration of the person's center of mass?
Consider a "round" rigid body with moment of inertia I = BMR², where M is the body's mass, R is the body's radius, and B is a constant depending on the type of the body. Rigid Body Uniform hoop Uniform solid cylinder Uniform spherical shell Uniform solid sphere 1 1/2 2/3 k 2/5 The center of the "round" rigid body is attached to a spring of force constant k, and then the body is made to roll without slipping on a rough horizontal surface. Due to the spring, it is expected the body will oscillate by rolling back and forth from its resting position. A. (6 Points) Determine the angular frequency and the period for small oscillations of the round rigid body. Express your answer in terms of B.