5. Bir merdivenin iki kolundan birinin uzunluğu 3 m ve ağırlığı 360 N, diğerinin uzunluğu 4 m ve ağırlığı 480 N dur. Merdivenin iki kolu tepede bir menteşeyle birleştirilmiş, ayrica yerden 0,90 m yükseklikte yatay bir iple birbirlerine sürtünmesiz yatay bir düzlem üzerinde dengede durmaktadır. İpteki gerilmeyi, menteşedeki tepki A 4.00 m 3.00 m bağlanmışlardır. Merdiven 0.90 m kuvvetinin bileşenlerini ve zeminin normal tepki kuvvetlerini hesaplayın.

Q: Ql. EI 2EI a A M.

A: Detailed solution below. Hope it will help you. Good Luck.

Q: Determine the reactions at the supports.

A:

Q: A 5-m cantilever beam carries 8 kn/m uniformly distri pan. Two meters from its free end exists an…

A:

Q: 80 KN -60 kN 4 m 80 kN 3m

A:

Q: Two high strength flexible steel cables AB and AC are fastened to the ceiling of a building through…

A: above given condition we have to find tension in both ropes AB and AC

Q: 20 KN 20 KN A 20 KN/m C 20 KN/m 20 KN E 20 KN/m F G 20 KN/m 30 KN/m K 20 KN/m J 20 KN/m 30 KN/m 1.50…

A: For Beam AB ∑FY= 0 RA+RB= 20+20×(1.5+1+1+1+0.5) =120kN Taking Moment at A ∑MA=0 5RB=…

Q: 4. Determine the absolute maximum moment in the beam due to the loading shown. 30 kN 20 kN 10 kN 15…

A:

Q: 3. Reactions on support E: Ex, Ey and Me for a 4. Reactions in cable to F: • Equilibrium Equations:…

A:

Q: 1.8 m 1.8 m troorl 0.80 kN 1.38 N 25° 1.5m,. 2.1 m.

A:

Q: 12. Determine the reactions at the supports, using moment distribution method 2m 40 kN 2m t 21 m 2…

A: Given : Required : Support reactions using moment distribution method

Q: 2. Solve for the horizontal and vertical components of the reactions of the supports.

A: Given: Truss with loading as shown in figure

Q: Find the force member CH.

A: solution  these types of the question can be solved by using the method of joints concept

Q: 5) Obtain the support reactions for the system given below. A and B are pin supports C is a hinge.…

A:

Q: The vertical mast supports the 5.8-kN force F and is constrained by the two fixed cables BC and BD…

A: Given:- The magnitude of the force F = 5.8 N  The force is constrained by the two cables BC and BD…

Q: A IS 04 KN 15.VW KN B 6-55KN 6.XY KN 1.5 m 1.5 m 1.5 m 2.WX m 2.45m

A: ###Calculate reactions ofpoint A, B , C using equilibrium equations

Q: rces

A: Draw free body diagram

Q: Determine the force in member CD Determine the force in member DG Determine the force in member DH

A:

Q: 3 kN 2 kN 3 30

A:

Q: Determine the magnitude of the moment reaction at A. Answer in kN-m rounded off to 2 decimal places.…

A: Given Data Pin connection at B, C and D.  Determine the magnitude of the moment reaction at A.

Q: or the frame shown, the Moment Distribut )to draw the shear and bending moment ettlement of 0.25…

A: In the above question, a frame is given with all information we need to determine the following…

Q: The Fink Truss is supported by a hinge at A and by rollers on a 3 to 4 slope at B. The bracing bars…

A:

Q: Kindly refer to the given figure below. calculate the support reactions at point A,B & C. NOTE: The…

A:

Q: #2. Calculate the structural period (structure is Concrete special moment-resisting frame)? Does it…

A: Concrete special moment-resisting frame is provided.To calculate- Structural period

Q: The light right-angle boom which supports the 540-kg cylinder is supported by three cables and a…

A: Given:- The mass of the cylinder = 540 kg The light right-angle broom is supported by three cables…

Q: Find the vertical reaction at roller support. 20 KN 10 KN 4 000 20 KN 4 0000 AO

A: To find out the reaction at roller support.

Q: The tie rod is used to support this overhang at theentrance of a building. If it is pin connected to…

A: Introduction-  Angular velocity or rotational speeds, also described as angular frequencies vector,…

Q: Determine the resultant internal loadings acting on the cross section through point C. Assume the…

A:

Q: (A)Determine the roller support. (B)Determine the vertical reaction at the hinge support.

A:

Q: PROBLEM 2 Determine the reactions at the supports A and E ume The joints C and D are fixed…

A:

Q: 4. The two beams ABC and DE are simply supported at A, B and E, with roller support at C. Three…

A: Given values: Drawing free body diagram of the beams:

Q: 2.3.2

A:

Q: a. Determine the raaction foroes at point A (pin support) and paint D (roller support) b. Calculete…

A: We have to find reaction forces at point A and D. And also calculate resultant forces And the angle…

Q: 30 kN/m Hinge I1.6 m 200 kN 10.4 m

A:

Q: The beam ABC, built into the wall at A and supported by a cable at C, carries a distributed load…

A: Introduction- A beam is a structural component that is created to prevent loads that are delivered…

Q: IIL Complete the horizontal angle measurement note Result Reviewer Sight Reading Angle Face to 11 A…

A:

Stair construction and layout

Stair is a type of vertical transportation in a building which consist of a series of steps in a flight of stairs that enable the vertical movement of people and materials from one floor to another. A staircase consists of steps that comprises of riser & tread, handrail, baluster, stair stringers, newel post and waist slab. The construction of staircase with all the components is termed as stair construction. A staircase is an enclosure that contains the entire stairway. The materials used for the construction of stairs are bricks, reinforced cement concrete, stone, lumber, steel and a combination of these materials.