5. A9.0 m beam of uniform width is supported as shown by supports S1 and S2. Given the weight of the beam is 200N and is loaded as shown, determine the normal forces, S1 and S2, exerted on the beam. Assume the weight of the beam acts at the midpoint of the beam. Determine if it is possible to move the 300 N object to a location on the beam which will result in the beam "tipping."

5. A9.0 m beam of uniform width is supported as shown by supports S1 and S2. Given the weight of the beam is 200N and is loaded as shown, determine the normal forces, S1 and S2, exerted on the beam. Assume the weight of the beam acts at the midpoint of the beam. Determine if it is possible to move the 300 N object to a location on the beam which will result in the beam "tipping."

Name: A 9.0 m beam of uniform width is supported as shown by supports S1 an
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A 9.0 m beam of uniform width is supported as shown by supports S1 and S2. Giventhe weight of the beam is 200 N and is loaded as shown, determine the normal forces,5.S1 and S2, exerted on the beam. Assume the weight of the beam acts at themidpoint o

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the shown frame structure, the uniform beam AB weighs 400 lb and the uniform column CF weighs 1,800 lb. If the dimensions a = 3.2 ft, b = 9.5 ft, and c = 4.5 ft, determine the magnitude of the support force reaction at pin A. Answer must include 1 place after the decimal point and have proper units.
A crane boom is supported as shown. The boom has a mass of 660 kg and the box on the end of the cable has a mass of 98 x 10 kg. Assume that the center of mass for the boom is half way along its 15 meter length. Calculate the tension in the upper (diagonal) cable required to support the crane in equilibrium. The cable angle with the ground is 45 degrees and the boom angle with the ground is 60 degrees.
A uniform plank is 5.00 m long and weighs 100 N. The cord that attaches to the plank 1.00 m from the bottom end holds it from sliding. There is no friction between the floor and beam and the wall and beam. Find the tension in the cord. Hint: Find theta and alpha. Think about where you will put the axis of rotation.
A force of 1000 lb is applied to the 600-lb horizontal beam supported by a hinge at A and a roller at B on a smooth surface. If the pin support at A suddenly fails, calculate the magnitude of the force of the roller at B acting on the beam at that instant, by modelling the beam as a uniform slender bar. Present your answer in lb using 3 significant figures. 4 13 1000 lb -8 ft- B -2 ft-
QU. Determine the support reactions on the member. The collar at A is fixed to the member and can slide vertically along the vertical shaft. 200 N 2 m 2 m- Figure.
6.62 Neglect the mass of the pulleys and the link. The block has a weight of 230 lb and the cord is attached to the pin at B. The pulleys have radii of r1 = 2 in. and r2 = 1 in. Determine the force P on the cord. Determine the angle θ that the pulley-supporting link AB makes with the vertical.
A Fixed crane, as given in the figure, has a mass of 1000kg and is used to lift a 2400kg crate. It is held in a place by a point A and a roller B. The center of gravity of a crane is located at G. Determine the components of the reactions at A and B.
1. The rectangular plate is suspended from verti- cal cables and is in equilibrium. The mass, m, of the plate and the dimension d are given. The weight of the plate acts through the center of the rectangle. What are the tensions T4, T; and Tc in each of the three cables? 1.5d B 2.5d 10.75d d H
Determine the force equivalent to the distributed load and its point of application on the beam. Then determine the support reactions on the beam.
Beam AC is loaded with the distributed load shown, where the magnitude of the distributed load is w, = 700 lb/ft at A and 300 lb/ft at C. The support at B is fixed and the support at C is a roller. Determine the reactions at the beam supports. The solution to this problem must include a free-body diagram of the beam and a sketch of the coordinate system used to apply EF = 0 and EM = 0. wo 300 lb/ft A В 5 ft 7 ft
A 38.0 kg beam is attached to a wall with a hinge while it’s far end is supported by a cable such that the beam is horizontal. If the angle between the beam and the cable is θ = 69.0 ° what is the vertical component of the force exerted by the hinge on the beam?
Frames & Machines The truck shown is used to deliver food to aircraft. The elevated unit weighs 2000 Ib with center of gravity at G. 1- Derive the expression for the force in the hydraulic cylinder AB as a function of 0 (the angle that member FD makes with the horizontal). 2- Plot the force over the range 0° < 0 < 45° and discuss your observations. Note: | would suggest that you first solve the problem based on the position (angle) shown. You will need to determine the length of members FD and FB before solving the problem for arbitrary 0. Note that the location of the roller at D and hence the force reactions will change as 0 varies. 40" 17" 57" C 54" E 54" H AB