Solve both please 5. A closed-loop control system transfer function T(s) has two dominant complex conjugate poles.Sketch the region in the left-half-plane where the complex poles should be located to meet thegiven specifications.c) SS 0.707, 5s w, < 10e) S2 0.6. w, < 6

Answered: Image /qna-images/answer/e9170607-adb0-420e-bb2d-cf17b7180941.jpg

Answered: 5. A closed-loop control system…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Similar questions

A signal generator having a source resistance of 50 2 is set to generate a 1 kHz sinewave. Open circuit terminal voltage is 10 V peak-to-peak. Connecting a capacitor. across the terminals reduces the voltage to 8 V peak-to-peak. The value of this capacitor is -HF. (Round off to 2 decimal places).
6. Consider the electrical circuits shown in figure a.) and b.). For each circuit determine the transfer function C/2 C12 2R 2R (a) R (b)
Answer with explanations..
A sinusoidal signal of 2 kHz frequency is applied at the input of a delta modulator with a step size of 0.1 volt. The sampling rate of the delta modulator is 20000 samples per second. What will be the maximum amplitude of the sinusoidal signal if there is no slope overload distortion?
QUESTION 1 Design a high efficiency 3.3 V, 5A d.c.to d.c. power converter from a 4 to 5.5 Vdc source. The maximum allowable inductor current ripple and output voltage ripple are 0.1A and 20 mV, respectively. Assume a switching frequency of 20 kHz. a) Design a suitable converter power circuit using a MOSFET switch, showing all calculation of inductor and capacitor values and drawing a circuit diagram of the final design including component values. Indicate the peak inverse voltage and forward current rating of any diode required, and the maximum drain- source voltage of the MOSFET. b) On the Schematic diagram, draw the path of the current flow during the ON time and the OFF time. c) Describe the effect of changing the values of the inductor and the capacitor in the circuit. d) What is the effect of switching frequency in the circuit? e) Draw the schematic diagram of a circuit with the output voltage higher than the input voltage.
State the advantages and disadvantages of the block diagram reductio technique.
2. What is load frequency control? Which involves?
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
Q3: chopper , Duty cycle D= ( 0.2,0.3,0.4 0.6, 0.7, 0.9) use the DC-DC converter relations to analyse the behavior of Step dawn,step up and buck boost converter respectively applied period for the same square carrier signal T=10 ms and Vdc=10 v find the characteristic of Vout / D for each ? type converter and draw them precisely and give conclusion
What is a branch circuit? What is a small appliance branch circuit? What is a general purpose circuit? What is meant by “demand factor”?
Amplification in the ac domain cannot be obtained without the application of dc biasing level. a.Depending on the configuration b.Sometimes c.True d.False
Identify the given statement. FM and PM demodulators can actually reduce noise and increase the signal-to-noise ratio during the demodulation process by using limiters. This is known as the capture effect. Select your answer. The statement has no fixed information. The statement is false. The statement is true. The statement is a case-to-case basis.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning