5. A 1-m³ rigid tank has propane at 100 kPa, 300 K and connected by a valve to another tank of 0.5 m3 with propane at 250 kPa, 400 K. The valve is opened, and the two tanks come to a uniform state at 325 K. What is the final pressure? B

5. A 1-m³ rigid tank has propane at 100 kPa, 300 K and connected by a valve to another tank of 0.5 m3 with propane at 250 kPa, 400 K. The valve is opened, and the two tanks come to a uniform state at 325 K. What is the final pressure? B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Helium is compressed through a compressor steadily. At the inlet the pressure is and the temperature is . At the exit the pressure is and the temperature is . The power input is and the heat loss rate is during this process. Neglect the kinetic and potential energy changes. Assume helium is ideal gas with a constant specific heat and its specific heat ratio , which means that enthalpy can be calculated using . Calculate the work per unit mass _________
20. A tank contains 5kg of an ideal gas at 8atm and 60°C. A valve is opened and the mass of the gas is allowed to escape. If the final pressure in the tank is 3.4atm. What is the final temperature in the tank? a. -131.5613°C b. -119.0681°C c. -118.7652°C d. -114.9056°C
A rigid container, perfectly insulated against heat, is divided into two compartments by a curtain. One of the chambers contains 0.1 m3 of nitrogen at a temperature of 50°C and a pressure of 200 kPa. In the other compartment, there is oxygen in a volume of 0.2 m3 at a temperature of 100°C and a pressure of 300 kPa. By removing the curtain in between, the gases are mixed. Assuming constant specific heats,a) Find the final temperature and pressure of the mixture.b) Find the molar mass and partial pressures of the mixture gas.c) By removing the insulation around the rigid container, the gas mixture is heated up to 150°C. Find the final pressure, temperature change and total entropy change (T=25°C).
As shown in the figure, a 260-ft tank contains 25 lb of H20 initially at 30 lbf/in?. The tank is connected to a large steam line carrying steam at 200 lbf/in?, 450°F. Steam flows into the tank through a valve until the tank pressure reaches p2 = 160 lbf/in? and the temperature is 400°F, at which time the valve is closed. Steam at Tank 200 lbf/in.2. Valve (1) Initially: 30 lbfin.?, mı = 25 lb (2) Finally: P, lbfin.?, 400°F. 450°F (1) Determine the amount of mass that enters the tank, in Ib, and the heat transfer to the tank from its surroundings, in Btu.
Q/ A piston'cylinder arrangement, contains CO2 at 200 kPa. 350°C. The 40-kg piston has a diameter of 0.2 m and initially pushes against the stops. The atmosphere is at 100 kPa and 20°C. The cylinder now cools as heat is transferred to the ambient. a. At what temperature does the piston begin to move down? b. How far has the piston dropped when the temperature reaches ambient? c. Draw P-v diagram CO 20 on
Must answer the whole question completely..
Plot the process on pv diagram which show the state points relative to the vapor dome. Label the states 1,2,3.. to indicate the sequence of the change in state.
A and B tanks are fixed volume and connected with a valve. Initially the valve is closed. The volume of tank A is 2m³ and it is contained with propane at 116 kPa, 345 K. The volume of tank B is 0.72 m³ and is filled with propane at 152 kPa, 412 K. Calculate the pressure when the valve in the middle is opened and these two tanks become equilibrium at 367 K. kj = 0,1885 kg.K (R propane A B
1. Steam at a temperature of 250oC has a specific volume of 0.15436 m3/kg. What are the pressure, specific internal energy, enthalpy, and entropy?
Show detailed solution please.
Q1: Find the missing properties and give the phase of the substance a. H2O u = 2390 kJ/kg, T= 90°C h = ? v = ? x = ? b. H2O u = 1200 kJ/kg, P = 10 MPa T= ? x =? v = ?
Need in 20 mints Thanks