Submitting result report for thevenin equivalent circuit.Value4.1- voltage = 0.326v4.2 Vth =1.405 v Rth = 1.081 k ohm 4.3 Rth=1.081 k ohm RL = 0.326 v Design Practice 4. Design of Thevenin Equivalent Circuit1. Purpose: Design, manufacture, and measure Thevenin equivalent circuit and compare it with the original circuit and the theoretical value.2. Preparations* Basic Equipment and LinesFunction generator: 1 unitDC Power Supply (Regulated DC Power supply (Max 20 v or higher): 1 unitDigital Oscillo oscilloscopes with 2 Probe: 1Digital Multimeter (hereinafter DMM, using 220V alternating current): 1 unit40 cm connection wire: 4 red lines, 4 black lines (one side can be pluggedinto the instrument, the other tongs)Breadboard: 1Jumper Wire Kit: 1 piecePartsLead resistance: 1/4 w, 5% 1 each330 Ω, 390 Ω, 470 Ω, 1 ΚΩ, 1,2 ΚΩ, 3.3 ΚΩVariable resistance: 2 20kn.2W classes3. As shown in Figure 1 of the Design Practice Plan, the Thevenin equivalent circuit of the bridge circuitwith R load is obtained and compared through theory and experiment.5 V39047052ActionFigure 1 Bridge circuit3.3 kR₁-33052wwLove1.2 k3.1 What is the voltage applied to R and the current flowing to R in the bridge circuit?3.2 (a) Theoretically obtain V and R Th, design the Thevenin equivalent circuit, and submit the circuit diagram.(b) What is the voltage and current of R?3.3 (a) Thevenin equivalent circuit is to be obtained experimentally. Design an experimental circuit to obtain Vm andexplain the experimental procedure. Specify the position of the voltmeter (DMM). (b) Design an experimental circuit toobtain R Th and explain the experimental procedure. Specify the position of the ohmmeter (DMM).3.4 (a) Draw a Thevenin equivalent circuit with a load and a circuit that measures the voltage andcurrent of R. This value shall be equal to the value obtained in 3.1 and 3.2(b). 4. Experimental contents and analysisIf there are no other instructions, record the measurement up to three significant digits.*Connect the power lines of the DMM and the DC Power Supply to the 220 v power outlet and press the power buttonaccording to the instructions of the assistant before starting the experiment. Since all electrical and electronic equipmentconsists of parts whose characteristics change with temperature, accurate measurement should be performed afterwaiting for about 10 minutes after turning on the power. The power line must be connected to a 220 V power outlet |with a ground terminal. Otherwise, it is often impossible to measure!*Caution: Never change the voltage, current resistance measurement mode when the DMM is connected to the circuit! That is,change the measurement mode of the DMM before connecting to the circuit or element!* CAUTION: Always connect black lines to low voltage, or ground, and then connect black lines toeach other first, then red lines!4.1 (Original Circuit Measurement) Construct the circuit as shown in Figure 1 and measure the voltageapplied to R. Calculate the current flowing through R, from this. Record the voltage, the current.What is the error with the value calculated in 3.1? What is the reason for the error?4.2 (a) Measure and record Vm using the method in Experimental Plan 3.3. That is, after setting the DMM to theDC voltage measurement mode, remove Rt from Figure 1 and connect the DMM there to measure and recordthe voltage. (b) Measure and record R Th by the method in Experimental Plan 3.3. That is, after setting theDMM to the resistance measurement mode, remove the DC power supply from Figure 1 and connect theposition with a wire. Remove Rz and connect the DMM to the spot to measure and record the resistance. Whatis the error with the value calculated in 3.2? What is the reason for the error?4.3 Set the DMM to the resistance measurement mode, and then measure the variable resistance and adjust it toR The. Adjust the DC power supply output voltage to VTA. Construct the Thevenin equivalent circuit andconnect R,. Set the DMM to DC voltage measurement mode, measure the voltage applied to R, calculate thecurrent from it, and record each. What is the error between this value and the value calculated in 3.1 and thevalue measured in 4.1? Consider and determine the reference value when calculating the error.5. Matters to be consideredThe result report must be prepared in the form of a result report (example) at the front of the textbook, but be prepared byreviewing the followingDoes Thevenin's theorem work? Has the design been well practiced overall? On whatgrounds do you think it went well if it went well? If it didn't work out, what do you thinkis the reason? Do you think the Design Practice Plan is well prepared? Why do you thinkthe circuit or method you designed is wrong in the plan? What did you learn and what didyou feel? Why do you think we don't practice Norton equivalent circuits?

Answered: Image /qna-images/answer/c676366b-9ccf-405c-9a30-ecf2f8cb0854.jpg

Answered: 5 V 390 R₁-3305 ww 47052 Action Figure…

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...