5- The velocity of point C is 2 ft/sec to the right. Determine the angular velocity w of the link OA.b = 10 inches and 0 = 30°. %3D %3D

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: Determine the y_bar coordinate of the composite shape. Treat the bent corners as square and ignore…

A:

Q: 5. Work-energy principle to be useful in determining the change in the speed of a particle during a…

A: Work energy principle to be useful in determining the change in the speed of a particle during  a…

Q: pered gibs are adjusted by screws spaced out along the length of the gib

A: The statement mentions "Tapered gibs are adjusted by screws spaced out along the length of the gib".

Q: の5 の25 23

A: Representation of three-dimensional object in two dimensional is known as an orthographic…

Q: for the drawing shown : Draw the isometric.

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: w of sine's when ( a= 100° , A=10.8 B=6

A:

Q: 12-x2 了了少 Je

A:

Q: Which of the following statement is correct O 1. Reynolds number depends on the viscosity of fluid O…

A:

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…

A: Given:nA=0.3CA=120nB=0.5CB=30

Q: Die Ntef d CW ad d 107 30T 167 327

A:

Q: Draw chalk diagram of all sections

A: To draw section views

Q: Place the labels with the most accurate description on the micrograph at locations A, B, and C, as…

A: given; Place the labels with the most accurate description on the micrograph at locations A, B, and…

Q: P? P G P

A:

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 180 KN,…

A: Given : The shear force in this section is The diagram is,

Q: В |C O2 4 D 3 A E (201 5 F D 6 H at c I G Needle

A:

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A:

Q: Filler rod material is same base metal used in gas welding process. Select one: True False

A: Above statement is true.

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: 9

A: Dehydrator & Desalter

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: Y 8 12 8 12 R= 3

A:

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: Define and explain hookes law

A:

Q: Draw front, top and then left side view.

A:

Q: how did the equation simplify to a = 0.984?

A:

Q: The compressor is used to increase the flow energy of the gas Select one: True O False

A: Compressor is a mechanical device which used to increase the pressure of a gas in exchange of…

Q: Question No. 5 Find out the missing number in the series given below: 6, 13, 28, 59, ?, 249 O 124 O…

A: here, (6×2)+1 =13 (13×2)+2= 28 (28×2)+3 =59 (59×2)+4 = 122 (122×2)+5 = 248

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: During the governor regular working time the sleeve moves up with 16mm due to the effort of 225N…

A: Given that, The effort of the governer, F=225 N and the movement of the sleeve is, x=16 mm=0.016 m,

Q: 3. Write the information from the following weld symbol.

A:

Q: y (x- 6y)dx - x (2x - gy) dy = 0; x =1 , y = 1

A:

Q: Do number 13.12

A: Given Data Qr=24000 BTU/hr EER=11 Cost= 14 cents per kWh

Q: What is a bending moment?

A: Bending moment: Bending moment is a moment which developed in any structure or body when a force or…

Q: non exact .3

A:

Q: when calculating the hc, why are adding the x as well ?

A:

Q: Explain briefly Hooke’s Law

A: Given data: Hooke’s Law  To Explain:- Hooke’s Law  Elasticity:-the elasticity of a material refers…