RF1 RF1 Rsi Rs2 5 Select appropriate components using standard 5 percent resistor values to obtain a gain of magnitude approximately equal to 1,000 in the circuit of Figure P8.44. How closely can you approximate the destred gain? Compute the error in the gain, assuming that the 5 percent tolerance resistors have the nominal value.

RF1 RF1 Rsi Rs2 5 Select appropriate components using standard 5 percent resistor values to obtain a gain of magnitude approximately equal to 1,000 in the circuit of Figure P8.44. How closely can you approximate the destred gain? Compute the error in the gain, assuming that the 5 percent tolerance resistors have the nominal value.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter28: Direct-current Circuits

Section: Chapter Questions

Problem 28.21P: Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0...

See similar textbooks

Similar questions

Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
Consider a circuit that consists of a real battery with an emf and an internal resistance of r connected to a variable resistor R. (a) In order for the terminal voltage of the battery to be equal to the emf of the battery, what should the resistance of the variable resistor be adjusted to? (b) In older to get the maximum current from the battery, what should the resistance variable resistor be adjusted to? (c) In order for the maximum power output of the battery to be reached, what should the resistance of the variable resistor be set to?
An ECG monitor must have an KC time constant lessthan 1.00102s to be able to measure variations involtage oversmall time intervals, (a) If the resistance of the circuit (duemostly to that of the patient's chest) is 1.00kTwhat is the maximum capacitance of the circuit?(b) Would It be difficult in practice to limit the capacitance to less than the value found in (a)?
Digital medical thermometers determine temperature by measuring the resistance of a semiconductor device called a thermistor (which has a=0.06/C ) when it isat the same temperature as the patient. What is a patient’s temperature if the thermistor’s resistance at that temperature is 82.0% of its value at 37C (normal bodytemperature)?
Using your understanding of the nature of internal energy and temperature, explain why we might expect the resistance of a solid to increase if its temperature increases.
How does the resistance for copper and for silicon change with temperature? Why are the behaviors of these two materials different?
(a) Digital medical thermometers determine temperature by measuring the resistance of a semiconductor device called a thermistor (which has a= - 0.0600/°C ) when it is at the same temperature as the patient. What is a patient's temperature if the thermistor’s resistance at that temperature is 82.0% of its value at 37.0°C (normal body temperature)? (b) The negative value for a may not be maintained for very low temperatures. Discuss why and whether this is the case here. (Hint: Resistance can’t become negative.)
Consider a resistor made from a hollow cylinder of carbon as shown below. The inner radius of the cylinder is Ri= 0.20 mm and the outer radius is R0 = 0.30 mm. The length of the resistor is L = 0.90 mm. The resistivity of the carbon is =3.5105 m. (a) Prove that theresistance perpendicular from the axis is R=2L1n(R0Ri) . (b) What is the resistance?
(a) When the switch S in the circuit of Figure P28.14 is closed, will the equivalent resistance between points a and b increase or decrease? State your reasoning. (b) Assume the equivalent resistance drops by 50.0% when the switch is closed. Determine the value of R.
A 160F capacitor charged to 450 V is dischargedthrough a 31.2k resistor, (a) Find the time constant.(b)Calculate the temperature increase of the resistor, given that its mass is 2.50 g and its specific heat is 1.67kJ/kg °C,noting that most of the thermal energy is retained in the short time of the discharge, (c) Calculate the new resistance, assuming it is pure carbon. (d) Does this change in resistance seem significant?
A flashing lamp in a Christmas earring is based on an RC discharge of a capacitor through its resistance. The effective duration of the flash is 0.250 s, during which it produces an average 0.500 W from an average 3.00 V. (a) What energy does it dissipate? (b) How much charge moves through the lamp? (c) Find the capacitance, (d) What is the resistance of the lamp? (Since average values are given for some quantities, the shape of the pulse profile is not needed.)
A 1,00-?O voltmeter is placed in parallel with a 75.0kresistor in a circuit, (a) Draw a circuit diagram of the connection, (b) What is the resistance of the combination? If the voltage across the combination is kept the same as it was across the 75.0-kresistor alone, what is the percent increase in current? (d) If the current through the combination is kept the same as it was through the 75.0-kresistor alone, what is the percentage decrease in voltage? (e) Are the changes found in parts (c) and (d) significant? Discuss.