(5) A spring-loaded piston-cylinder device is filled with 3.5 kg of steam at 3 MPaand 300°C. Initially, the spring exerts no force against the piston. The springconstant in the spring force relation F = kx is k = 1.4 kN/m and the piston area is129.255 cm?. The water now undergoes a process until its volume is reduced by21%. The final temperature of the water is:(a) 217.68°C(b) 223.95°C(c) 229.91°C(d) 235.12°C(e) 239.42°CSpringFluidD

Step by step solution is given below. Option B is correct.

(5) A spring-loaded piston-cylinder device is filled with 3.5 kg of steam at 3 MPa and 300°C. Initially, the spring exerts no force against the piston. The spring constant in the spring force relation F = kxr is k = 1.4 kN/m and the piston area is

(5) A spring-loaded piston-cylinder device is filled with 3.5 kg of steam at 3 MPa and 300°C. Initially, the spring exerts no force against the piston. The spring constant in the spring force relation F = kxr is k = 1.4 kN/m and the piston area is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2 A dividing wall divides an insulated container into two compartments as shown in the figure.…

A: please refer handwritten solution

Q: 10 lbm of ammonia (MW = 17), is heated inside a cylinder equipped with a piston. The initial…

A: Draw the P-V diagram and the T-S diagram. Here, 1 is the initial state of the system and 2 is the…

Q: (5) A spring-loaded piston-cylinder device is filled with 4 kg of steam at 2.5 MPa and 250°C.…

A: Given that, Mass of the steam, m=4 kg,Initial pressure of water, P1=2.5 MPa,temperature of water,…

Q: Question 1: Gasoline flows into the tank through two pipes. At A the velocity is 4 m/s. Determine…

A: The inlet velocity at pipe A is,The diameter at pipe A is,The diameter at pipe B is,The range of…

Q: he piston cylinder system shown below contains R-410a at 20°C and 100 kPa. If the temperature of the…

A: Given:R-410aT=210°CP1=100 kPaT2=50°C

Q: 10 lbm of ammonia (MW = 17), is heated inside a cylinder equipped with a piston. The initial…

A: Given Mass, m = 10 lbm Pressure, P = 63 psi Temperature, T1 = 50o F Temperature, T2…

Q: 4-118 A piston-cylinder device contains helium gas initially at 100 kPa, 10°C, and 0.2 m³. The…

Q: takes 675 J of work to compress quasi- culate the temperature

A: we have to determine the temperature of a isothermal system undergoing compression

Q: 100 grams of R-134a initially fill a weighted piston cylinder device at 60 kPa and -20°C. The device…

A: Refrigerants are used in cooling systems. When such gas is confined in a cylinder and heated its…

Q: Problem 2: A piston-cylinder device contains 50 kg of water at 250 kPa and 25 °C. The…

A: Given data: mass of water, m=50kg Initial pressure,P1=250kpa=P2 Initial temperature,…

Q: 3- A mass of 10 kg of saturated refrigerant-134a vapor is contained in a piston-cylinder device at…

A: Given data: Mass of saturated vapor refrigerant R-134a, m = 10 kg. The saturated vapor pressure in…

Q: Question 1: 4-20 A piston-cylinder device contains 0.15 kg of air initially at 2 MPa and 350°C. The…

Q: 10 lbm of ammonia (MW = 17), is heated inside a cylinder equipped with a piston. The initial…

A: m=10 lbm=4.53592 kgP1=63 psi=4.3437 barT1=50°F=283.15 KT2=100°F=310.928 K…

Q: As shown in the figure, a piston-cylinder assembly with a stopper contains R-410A, a refrigerant at…

Q: A piston–cylinder device contains 4 kg of argon at 250 kPa and 35°C. During a quasi-equilibrium,…

A: Given data: The mass of the argon is m=4 kg The pressure of the argon is P=250 kPa The temperature…

Q: Calculate the boundary work done by the system during this process

Q: 4. 0.5 kg of steam at 250°C is enclosed behind a piston in a cylin 0.9MPa. with the piston rigidly…

A: Givenm=0.5kgT1=250oCP1=0.9MPaP2=0.7MPa

Q: A rigid tank initially contains 4 kg of saturated liquid R-134a at 24C. A valve in the bottom of the…

Q: An ideal gas has a value of R = 58.8 ft·lb/lb·°R and k = 1.26. If 20 Btu are added to 5 lb of this…

A: According to the question, 20 BTU are added to the gas at constant volume. Therefore, the…

Q: A frictionless piston-cylinder device contains 2.5 kg of nitrogen at 100 kPa and 250 K. Nitrogen is…

A: According to the given dataThe mass of nitrogen is m = 2.5 kgThe initial pressure is P1 = 100 kPaThe…

Q: The heat transfer of gas during the process, in kJ. (2) The velocity of the piston at the final…

Q: Three kilograms of water at 30°C are placed in a piston cylinder device under 1.0 MPa absolute…

A: The mass of the water, The initial temperature of the water, The initial pressure of water, The…

Q: The initial conditions of 0.8 kg of carbon dioxide inside a piston-cylinder device are 300°C and The…

A: Given:mass of cabon dioxide, m=0.8 kginitial pressure, P1=100 kPainitial temperature, T1=300o C or…

Q: Steam is contained in a 2-L volume at a pressure of 2.0 MPa and a temperature of 400°C. If the…

A: Givenvolume of the steam v=2ltr=2×10-3 m3pressure, P=2MPatemperature T=400oCheat added Q=20kJ

Q: A weighted piston-cylinder device is initially filled with water as a saturated vapor at 500 kPa.…

A: According to the problem, the initial pressure of saturated water vapor is 500 kPa. From the…

Q: While the piston is pinned, a cylinder with a volume of 0.05 m3 contains 200 kPa pressure and 300 K…

A: Given: Initial temperature (T1)=300KInitial pressure (P1)=200kPaInitial volume (V1)=0.05m3Pressure…

Q: A 0.15 kg of air contained in a piston-cylinder device where the initial pressure was 2000 kPa and…

Q: If the pressure of a gas is a function of volume p(V)=(24atm lt)/V +.5atm (1atm/lt) V Determine the…

A: Given data Pressure of gas is a function of volume P(V) = 24V + 0.5 VWe have to find the work…

Q: A piston-cylinder container contains 14 lbm of refrigerant 134a at 180 psia with an internal energy…

Q: ia and 70 degrees F. More air is added to the tank until the pressure and temperature rise to 25…

A: Given: The initial mass of the air is m1=20 lbm. The initial pressure of the air is P1=20 psia. The…

Q: Water yapor is placed in a piston-cylinder device at 150°C and 0.3 MPa. Weights are placed on the…

Q: 4-40 Steam at 75 kPa and 8 percent quality is contained in a spring-loaded piston-cylinder device,…

A: Initial State,P1 = 75 kPa, Volume = 2 m3, Quality = 8% or X = 0.08,Final State,P1 = 225 kPa,…

Q: A frictionless piston-cylinder device and a rigid tank contain 2 kmol of an ideal gas at the same…

A: GIVEN DATA - Rigid tank contain 2kmol of ideal gas Temprature difference =10'C concept used- ideal…

Q: 4-65E A 10 ft³ tank contains oxygen initially at 14.7 psia and 80°F. A paddle wheel within the tank…

Q: An insulated, vertical piston–cylinder device is purchased from a manufacturer. Upon purchase, it…

A: From the steam table, the specific enthalpy of the saturated water at 200C is 83.9199 kJ/kg. From…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

(5) A spring-loaded piston-cylinder device is filled with 3.5 kg of steam at 3 MPa
and 300°C. Initially, the spring exerts no force against the piston. The spring
constant in the spring force relation F = kx is k = 1.4 kN/m and the piston area is
129.255 cm?. The water now undergoes a process until its volume is reduced by
21%. The final temperature of the water is:
(a) 217.68°C
(b) 223.95°C
(c) 229.91°C
(d) 235.12°C
(e) 239.42°C
Spring
Fluid
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A piston–cylinder device contains 0.05 m3 of a gas initially at 200 kPa. At this state, a linear spring that has a spring constant of 150 kN/m is touching the piston but exerting no force on it. Now heat is transferred to the gas, causing the piston to rise and to compress the spring until the volume inside the cylinder doubles. If the cross-sectional area of the piston is 0.25 m2, determine (a) the final pressure inside the cylinder, (b) the total work done by the gas, and (c) the fraction of this work done against the spring to compress it.
i need the answer quickly
Thermodynamics
Two different piston – cylinder devices each contain 1 kg of air. Initially, the temperature T = 300 K and %3D pressure P= 100 kPa of the gases are both the same in both cylinders. However, one of the cylinders is insulated and the other is not. Now, both of these gases inside the cylinders are let to expand in quasi- equilibrium processes until their pressures reach to 50 kPa. The expansion process takes place isentropically in the cylinder 1 and in the cylinder 2 the expansion process takes place reversible and isothermally. a) Plot in Excel the P-V diagrams of both processes. (Take k = cp / cv = 1.4) %3D b) Calculate the work done by the gases.
2.1-m3 of Helium contained in a rigid volume is initially at 52°C and 197 kPa. Calculate the heat transfer needed in kJ to increase the pressure to 790 kPa. Use Cv=3.116 kJ/kg-K and R=2.077 kJ/kg-K.
Consider a piston-cylinder device that consists of 2 kg of R-134a at 40°C and x = 0.7. The system is cooled until the temperature drops to 18°C. State the final phase of R-134a in the piston cylinder device and give the volume (m³) of the system at final phase.
please answer to me quickly
Air in a closed-piston cylinder is initially at 100 kPa and 27°C. It is then compressed until the pressure reaches 2 MPa in a polytropic process with n = 1.3. Determine how much boundary work in kJ/kg must be supplied into the system to make this process possible. Round your answer to the nearest whole number.
Eighteen kilograms of methang gas is confined inside a closed cylinder equipped with a piston which has an initial pressure of 3100 mmHg abs and 138°C. If the gas is cooled until its final pressure and temperature are 2340 mmHg gauge and 0°C, respectively, what is the amount of work done by the fluid in kJ?