5) A collar, C, has a mass, mc, is allowed to freely slide along rod AD and is attached to spring BC. The spring has an undeformed length of 10 cm and spring constant, k = 5000 N/m. %3D mc = 5.0 kg LAB = 10.0 cm LAD = 1.0N m2 %3D The system initially has a rotation rate of w = 15.0 rad/s, distance to collar LAC = 30.0 cm, and the collar has zero velocity with respect to the rod AD. a. What is the rotation rate of the assembly as the collar passes through a point 5.0 cm from point A (ie. LẠC = 5.0 cm)? b. What is the corresponding velocity of the collar relative to the rod.

5) A collar, C, has a mass, mc, is allowed to freely slide along rod AD and is attached to spring BC. The spring has an undeformed length of 10 cm and spring constant, k = 5000 N/m. %3D mc = 5.0 kg LAB = 10.0 cm LAD = 1.0N m2 %3D The system initially has a rotation rate of w = 15.0 rad/s, distance to collar LAC = 30.0 cm, and the collar has zero velocity with respect to the rod AD. a. What is the rotation rate of the assembly as the collar passes through a point 5.0 cm from point A (ie. LẠC = 5.0 cm)? b. What is the corresponding velocity of the collar relative to the rod.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 ) Derive a free body diagram with spring-mass-damper elements for given system. QUESTION 2 ) Derive equation of motion for given system in terms of m, c, k.
solve using laplace
A model for forced spring mass system is given by: ту" + су'+ ky rlt) (i) Find the steady state solution (y,) for case with value of m = 1, c = 4, k = 4 and r(t)= 2cost %D (ii) Find the solution (y. Y, ) that satisfies y(0) =1 and y '(0) =2 C +7 p
5. A rod of length L, Young's modulus E, cross-sectional area A and mass density p is installed as shown. Suppose m = pAL and kL / EA =1. Find the equations of motion Open Question m www f(t) x=0 x = L/2 x= L
7. A spring is attached to the floor. When a 125 g mass is placed on top of the spring it compresses by 0.26 m. What is the spring constant of this spring?
2. Consider a car suspension, modeled as a mass/spring/damper system (mass m, stiffness k, damping b). Suppose the height of the chassis is lo at rest, the height of the terrain below the driver varies as h(t), and the height of the chassis is denoted lo + y(t). (i.e., spring deflection away from rest is y(t) – h(t)). 2 (a) Give the transfer function G(s) = H(s) · = (b) Suppose the ground follows an oscillatory profile h(t) A cos(wx (t)) with magnitude A (in meters) and frequency w (measured in radians per meter). Suppose the car is traveling at a constant forward speed v. Using a frequency response analysis strategy, give the amplitude of oscillations experienced by the driver at steady state as a function of m, k, b, A, w, and v. Hint: You can't simply consider |G(iw)| to get the amplification in this case. (c) Suppose the ground varies by A = 5cm, w = 2 rad/m, and you are driving at v = 15 m/s. Using your answer to part (b), what amplitude of oscillation is felt by the driver when m…
Between a solid mass of 10 kg and floor, two slab of isolator, natural rubber and feltare kept in series as shown in Figure Q1(b). The natural rubber slab has a stiffnessof 3000 N/m and an equivalent viscous damping coefficient of 110 Ns/m. The feltslab has a stiffness of 12,200 N/m and an equivalent viscous damping coefficient of170 Ns/m. (i) Sketch the single degree of freedom spring-mass-damper system(ii) Determine the undamped and damped natural frequencies of the system inthe vertical direction. Neglect the mass of the isolator
A helical spring has spring constant k. If the wire diameter, spring diameter and the number of coils are all doubled then the spring constant of the new spring becomes
Can you solve it plz and can you explain that well.
Use the Finite Volume method to find general nodal equations for the CV of the geometry. Use the implicit method to find the rate of change of energy storage in the CV.
1. A spring mass system serving as a shock absorber under a car's suspension, supports the M 1000 kg mass of the car. For this shock absorber, k = 1 × 10°N /m and c = 2 × 10° N s/m. The car drives over a corrugated road with force %3| F = 2× 10° sin(@t) N . Use your notes to model the second order differential equation suited to this application. Simplify the equation with the coefficient of x'" as one. Solve x (the general solution) in terms of w using the complimentary and particular solution method. In determining the coefficients of your particular solution, it will be required that you assume w – 1z w or 1 – o z -w. Do not use Matlab as its solution will not be identifiable in the solution entry. Do not determine the value of w. You must indicate in your solution: 1. The simplified differential equation in terms of the displacement x you will be solving 2. The m equation and complimentary solution xe 3. The choice for the particular solution and the actual particular solution x,…