•5-53. The 20-mm-diameter A-36 steel shaft is subjected to the torques shown. Determine the angle of twist of the end B.

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: High precision in angularmeasurements can be made usinga sine bar. For using a 200 mm sinebar to…

A: Data available:Sine bar length is 200 mmL=200 mmDiameter of rolls is 35 mmd=35 mmInclined angle is…

Q: bäi The command using to insert :seal is

A: The Incident Command System is a standardized approach to the command, control, and coordination…

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: Given the isometric drawing, draw the multiview projection. The multiview projection of the glass…

A: Draw the isometric view.

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: Draft and annotate the below sketch using AutoCAD Note: colour the hatching lines with different…

A:

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: Pls use any CAD software to draw the sectional view of the solid attached in the image below.

A: FindWe need to draw the sectional view of the given object using CAD software.

Q: Figure 3 shows a product of tennis ball launcher in the market. Determine the problem statement,…

A:

Q: 9. To produce the line of intersection between the two cylinders, connect the project points using a…

A: Since we only solve up to three subparts, we will answer the first three. Please resubmit the…

Q: Develop two possible hierarchies for assembling a model from the parts given below: Top Pins…

A: Given question: Develop two possible hierarchies for assembling a model from the parts given below:…

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: To make the 3d sketch for each of the frames which contain the views in the plan

A:

Q: can make it in Solidwork

A: Given Structure To find 3D model

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Write the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS…

A: I have attached the image belowExplanation:

Q: State four espect to consider before selecting correct solvant

A:

Q: idk where you got the 4 from

A: The number of independent equations=5The number of unknowns=7To determine:Degree of freedom

Q: . Convert the octal number 23228 to its decimal number equivalent, (base-8 to base-10).

A: Givenoctal number =23228

Q: H.W praw load dingram alesfanding to the given-Shar dingram? 2nd (urve 10 2nd Garve sfin -10 Im Im

A: BMD(Bending moment diagram) is a diagram representing the variation of bending moment along the…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: • Use hexagonal head screw/bolt with jam locking nut through clearance holes to fix the two parts…

A:

Q: to move a force of 1713 lbs using a 100 psi what size bore in diameter would it need in inches

A: Given data: F=1713 lbsσ=100 psi Need to determine the size bore in diameter.

Q: Draw a FBD the tip to tail method please show steps

A:

Q: Sketch shaper machine and explane its parts?

A: Parts of a shaper function are, Base: The Base is fixed to the shop floor and built to take the…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on both…

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: What is the v-velocity at the centerline after refining the mesh

A: To explain: What is the v-velocity at the centerline after refining the mesh.

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: 1. Write the procedure for shaper process.

A: Shaper process is the process in which unwanted metal surface is removed by a single-point cutting…

Q: Draw figure (3) by using circle, polyline, loft, slice and union.

A:

Q: Match the given functions with the components of a wind turbine. Connects the rotor hub to the gear…

A: a) Main Shaft connects the rotor hub to the gearbox.

Q: Can someone show me how to do the roller, pin, and built-in supports( 2 each) and point them.

A:

Q: Gentlemen, please help to solve a,b,c as I faced confusing questions about screw jack. Conditions…

A: Given: The load to be lift, M = 3.2 ton = 3200 kg The screw pitch, d = 12 mm The diameter of screw…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: Name the feature shown below.

A: The given figure is of

Q: Which of the following statement is correct in terms of degree of freedom? Select one: O Moving left…

A: