•5-49. The A-36 steel axle is made from tubes AB and CD 400 mm and a solid section BC. It is supported on smooth bearings that allow it to rotate freely. If the gears, fixed to its ends, are subjected to 85-N•m torques, determine the angle of twist of gear A relative to gear D. The tubes have an outer diameter of 30 mm and an inner diameter of 20 mm. The 85 N-m 250 mm 400 mm solid section has a diameter of 40 mm. 85 N-m

•5-49. The A-36 steel axle is made from tubes AB and CD 400 mm and a solid section BC. It is supported on smooth bearings that allow it to rotate freely. If the gears, fixed to its ends, are subjected to 85-N•m torques, determine the angle of twist of gear A relative to gear D. The tubes have an outer diameter of 30 mm and an inner diameter of 20 mm. The 85 N-m 250 mm 400 mm solid section has a diameter of 40 mm. 85 N-m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The two 1-kg gears A and B are attached to the ends of al 3-kg slender bar. The gears roll within the fixed ring gear C, which lies in the horizontal plane. (Figure 1) Figure 150 mm 400 mm- 150 mm Part A If a 10-N m torque is applied to the center of the bar as shown, determine the number of revolutions the bar must rotate starting from rest in order for it to have an angular velocity of WAB = 22 rad/s. For the calculation, assume the gears can be approximated by thin disks. Express your answer using three significant figures. ►View Available Hint(s) the number of revolutions = Submit Provide Feedback VAE vec ? Next >
5.3 Please help. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
127 2 a В А 540 rev/min - - D 40T q3..Shaft a transmits 7 hp. Determine the reaction at bearings A and C knowing that these bearings will support thrust loading. The helical gears have 17.5° normal pressure angle and 25° helix angle and 14 normal diametral pitch. Dimensions in inches.
Please answer: 3, 4, 5, 6, 8, 9, 10, 12 The only correct answers are 1 (0), 2 (0), 7 (point A). #11 is 2. The rest are incorrect. Please do not submit the same answer you submitted for my original question. The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the datum for gravitational potential energy is set as shown below, the the gravitational potential energy of the wheel at the state 1 is 0 N m(two decimal places) (ANSWER IS 0) (2) If the datum for gravitional potential energ is set as shown below, the gravitational potential energy of…
Completely solve and box the final answer. Write legibly Determine the maximum mass (kg) can be lifted at E if the 10-HP motor A has a maximum rotation speed of 300 rpm where the diameter of the shaft AB and CE are 10 mm and 15 mm, respectively. The allowable shearing stress is 1 GPa with an F.S. of 1.2 for both shafts. Neglect the deformation of the cable at E.Where: Radius of the gear at B, rB = 100 mm Radius of the gear at C, rC = 150 mm
PLEASE ANSWER NUMBER 2 MECH 222: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
Three Wheels. Three rubber wheels are mounted on axles so that they make tight contact with each other and their centers are on a line. The wheel on the far left axle is connected to a motor that rotates it at 35.0 r.p.m.; and drives the wheel in contact with it on its right which, in turn, drives the wheel on its right. The left wheel (Wheel 1) has a diameter of d₁ = 0.22 m, the middle wheel (Wheel 2) has d₂ = 0.32 m, and the far right wheel (Wheel 3) has d3 = 0.48 m. (a) If Wheel 1 rotates clockwise, in which direction does Wheel 3 rotate? (b) What is the angular speed of Wheel 3, and what is the tangential speed on its outer edge? (c) What arrangement of the wheels gives the largest tangential speed on the outer edge of the wheel in the far right position (assuming the wheel in the far left position is driven at 35.0 r.p.m)? (d) What is the largest tangential speed on the outer edge of the wheel in the far right position? (a) (b) Angular speed of Wheel 3: (c) Number Tangential speed…
for the machinery.
Please and thank
The pinion (gear 2 on shaft a) rotates at 635 rev/min clockwise and transmits 1305 W through the idler pair (gears 3 and 4 on shaft b) to the output gear (gear 5 on shaft c). Gears 2 and 3 have a module of 2 mm, and gears 4 and 5 have a module of 3 mm. Pressure angles are all 20 degrees. Solve for the magnitude of the force that shaft b must apply to gears 3 and 4 to maintain static equilibrium in the figure shown here. The figure is not to scale. Please give your answer in units of newtons. geard 615 verimin m₂ = M₁ = 2mm 187 327 187 487 MG M₁ = ₂ = 3mm 0=20° I solved it and дог 692.60 Х សុំ But fr is not correct
The shaft is made of A-36 steel. It has a diameter of 1 in. and is supported by bearings at A and D, which allow free rotation. Determine the angle of twist of gear C with respect to B.
*10-23. If the gears are subjected to the torques shown, determine the required diameter of the A36 steel shaft to the nearest mm if rdi - 60 MPa. 300 N-m 100 N-m 200 N-m