5-34. Determine the horizontal and vertical components of reaction at the pin A and the normal force at the smooth peg B on the member. 0.4 m 130° 0.4 m F = 600 N 30°

Q: P4-1. Draw the free-body diagram of object. 600 N m -2 m- 3m

A: Given data Applied moment = 600Nm To draw the free body diagram of the object with given moment

Q: 4-49. Determine the angle o at which the applied force P should act on the pipe so that the…

A:

Q: 3-7. The man attempts to pull on the tree using the cable and small pulley arrangement shown. If the…

A: Given that:the man attempts to pull down the tree using the cable and small pulley arrangement shown…

Q: P4-7. Determine the force P needed to cause impending motion of the block. W = 200 N Fim-

A: Given Data: The force acting on the block is P. The coefficient of friction is µ = 0.3 The weight…

Q: 5-34. Determine the horizontal and vertical components of reaction at the pin A and the normal force…

A: Given data F = 600 N

Q: 3-3. Knowing the forces in members A and C, determine the forces FB and FD acting on members B and D…

A: To determine:The forces FB and FD

Q: 5-27. As an airplane's brakes are applied, the nose wheel exerts two forces on the end of the…

A:

Q: 4-58. The coefficients of static and kinetic friction between the drum and brake bar are p. = 0.4…

A: Draw the free-body diagram of the brake bar. Draw the free-body diagram of the drum.

Q: 3-39. The 30-kg pipe is supported at A by a system of five cords. Determine the force in each cord…

A: Given : m = 30 kg Then weight of the block W = mg = 30*9.81 = 294.3 N     consider slope BD, so…

Q: 5-14. The shelf supports the electric motor which has a mass of 15 kg and mass center at G. The…

A: The shelf supports the electric motor which has a mass of mm = 15 kg and mass center at G.The…

Q: T 30°- 50 mm 20 mm-| 10 mm The operation of the fuel pump for an automobile depends on the…

A: Solution:

Q: Bar GHJ is subject to a 25 lb force and is supported by a pin in a smooth slot at G, a weightless…

A: The link at H is weightlessThe weight of GHJ is

Q: 6-70 Determine the horizontal and vertical components of force at pins B and C. The suspended…

A:

Q: *5-16. Determine the tension in the cable and the horizontal and vertical components of reaction of…

A:

Q: 3 3-7. The device shown is used to straighten the frames of wrecked autos. Determine the tension of…

A:

Q: 3-21. The 10-lb weight is supported by the cord AC and roller and by the spring. If the spring has…

A:

Q: 3/14 The wall-mounted 2.5-kg light fixture has its mass center at G. Determine the reactions al A…

A: The free body diagram, write the known and determine the weight of the lamp :W = mgW = 2.5 x 9.81W =…

Q: 4-62. The uniform hoop of weight W is subjected to the horizontal force P. Determine the coefficient…

A:

Q: 3-23. Determine the unstretched length of spring AC if a force P 80 lb causes the angle 6 60° for…

A:

Q: *4-24. Determine the distance d for placement of the load P for equilibrium of the smooth bar when…

A: Taking Free body diagram of the bar, ∑Vertical forces = 0P-R×cos(θ)=0P=R×cos(θ)∑Moment about…

Q: 4-37. The rod assembly is used to support the 1.25-kN cylinder. Determine the components of reaction…

A: Since the member CD is a 2 force member, the force exerted on the member will be in the z-direction.…

Q: Determine the reactions at the supports.

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: 5-55. Determine the horizontal and vertical components of force which pin C exerts on member ABC.…

A: Consider free body diagram of the whole frame. Reactions at roller support 'A' and hinge support…

Q: F4-3. The truss is supported by a pin at A and a roller at B. Determine the support reactions. 10…

A: Draw the free body diagram of the truss:   Find AD: AD=EC+AE cos45°AD=2 m+4 cos45°AD=4.83 m…

Q: Based on Problem 5-87 from the textbook. Both pulleys are fixed to the shaft and as the shaft turns…

A:

Q: 1 m aile Prob. 5-82 ket Inthree di 5-83. Both pulleys are fixed to the shaft and as the shaft turns…

A: (A) Solution: To find the belt in tension we use the equilibrium condition in x axes. Take…

Q: The ramp of a ship has a weight of 250 lb and a center of gravity at G. Determine the cable force in…

A: Given: W = 250 lb

Q: Determine the components of these reactions if A ex only x and z components of force and B exerts x,…

A: Draw the FBD for the given question.

Q: The smooth uniform rod AB is supported by a ball-and-socket joint at A, the wall at B, and the cable…

A: Since the figure and dimension are not provided, Assuming a suitable figure and dimension as shown…

Q: P5-3. then draw the free-body diagrams of each member of the identify any two-force members, and…

A: Break the given frame into two parts AB and BC. Understand that the Uniformly varying load can be…

Q: R4-6. A vertical force of 400 N acts on the crankshaft. Determine the horizontal equilibrium force P…

A: Apply static equilibrium equation…

Q: P4-7. Determine the force P needed to cause impending motion of the block. 1m w = 100 N EIm . = 0.4

A: Given data: Weight of the block, W = 100 N. Coefficient of friction, µs = 0.4. Consider slipping…

Q: 3-38. The block has a weight of 20 lb and is being hoisted at uniform velocity. Determine the angle…

A:

Q: 4-32. Determine the force P of Fig. P4-32 that will maintain equilibrium.

A: T is tension in the string attached at left side to the mass.T' is tension in the string attached at…

Q: 4-15. The 10-kg uniform rod is pinned at end A. If it is subjected to a couple moment of 50 N-m,…

A: Given data: Mass of uniform rod = 10 kg                     Magnitude of couple applied = 50 N m…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.