3.5-1a. TCP RTT estimation and timeout value. Suppose that TCP's current estimated values for theround trip time (estimated RTT) and deviation in the RTT (DevRTT) are 300 msec and 13 msec,respectively. Suppose that the next two measured RTTS are 330 msec and 240 msec respectively.We want to calculate TCP's RTT estimate, and the value of TCP's timeout interval. Note that given anew measured RTT, you should first compute devRTT, then estimated RTT (the textbook incorrectlyreverses those computations), and then (lastly) the timeout interval. Use the values of a = 0.125, B =0.25.Following the newly measured RTT of 330 msec, what is the new value for devRTT in msec? [Note:round your answer to the nearest msec - enter an integer value, do not include any decimalplaces/point or any leading zeros, but keep your full resolution value of devRTT handy and use it inany later calculations you perform using devRTT.

Answer is explained below in detail

5-1a. TCP RTT estimation and timeout value. Suppose that TCP's current estimated values for the und trip time (estimated RTT) and deviation in the RTT (DevRTT) are 300 msec and 13 msec, spectively. Suppose that the next two measured RTTS are 330 msec and 240 msec respectively. We want to calculate TCP's RTT estimate, and the value of TCP's timeout interval. Note that given a ew measured RTT, you should first compute devRTT, then estimated RTT (the textbook incorrectly verses those computations), and then (lastly) the timeout interval. Use the values of a = 0.125, B 25. = ollowing the newly measured RTT of 330 msec, what is the new value for devRTT in msec? [Note: und your answer to the nearest msec - enter an integer value, do not include any decimal aces/point or any leading zeros, but keep your full resolution value of devRTT handy and use it in hy later calculations you perform using devRTT.

5-1a. TCP RTT estimation and timeout value. Suppose that TCP's current estimated values for the und trip time (estimated RTT) and deviation in the RTT (DevRTT) are 300 msec and 13 msec, spectively. Suppose that the next two measured RTTS are 330 msec and 240 msec respectively. We want to calculate TCP's RTT estimate, and the value of TCP's timeout interval. Note that given a ew measured RTT, you should first compute devRTT, then estimated RTT (the textbook incorrectly verses those computations), and then (lastly) the timeout interval. Use the values of a = 0.125, B 25. = ollowing the newly measured RTT of 330 msec, what is the new value for devRTT in msec? [Note: und your answer to the nearest msec - enter an integer value, do not include any decimal aces/point or any leading zeros, but keep your full resolution value of devRTT handy and use it in hy later calculations you perform using devRTT.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

5. Suppose that TCP's current estimated values for the round trip time (estimated RTT) and deviation in the RTT (DevRTT) are 200msec and 15 msec, respectively. Suppose that the next two measured values of the RTT are 200msec and 298 msec respectively. What is the TCP timeout after the second RTT? Use the values of a = 0.125, B = 0.25. Round your answers to two decimal places. (Answer in msec) MWELT
Consider the following 8-bit forwarding table: Prefix 1001 1100 1001 001 Other Link Interface 1 2 3 Assume the router uses longest prefix matching. To which link would a datagram with address 1101 1011 be sent? O Link interface 4 Link interface 2 O Link interface 3 Link interface 1
Provide a succinct explanation of the significance of the operator precedence.
Is this correct or incorrect? Assume that on a TCP connection, the most recent SampleRTT is 1 second. The current TimeoutInterval value for the connection must be larger than one second.
Consider a TCP connection with the following parameters: a) Initial ssthreshold = 4 segmentsb) Round Trip Time (RTT) = 10 millisecondsc) Timeout period = 40 millisecondsd) Segment size = 3900 bytesThe TCP connection was used to transfer 17 data segments. While sendingthe segments, data segment 7 and data segment 15 were lost the first timethey were sent (but arrived at the receiver properly when retransmitted).There were no other segment losses apart from the aforementioned. Assumethat data segments received out-of-order are buffered at the receiver. Whatis the average throughput obtained in sending all the data segments (inbytes/sec) including draw a diagram to show the communication process in detail.
i need the answer quickly
Consider a TCP connection between Host A and Host B. Suppose that the TCP segments traveling from Host A to Host B have source port number x and destination port number y. What are the source and destination port numbers for the segments traveling from Host B to Host A?
In the TCP we are using AIMD for congestion control, assume that after every fourth transmission timeout occurs. The slow start phase always starts with 1 MSS( maximum segment size) and the initial threshold window size is 8 MSS. What will be the threshold value (in MSS) when the threshold become constant? [Note: Always take a floor value if your threshold is in decimal.]
Calculate the loss rate L for TCP over "long fat pipe" with 1500-byte segments, 100ms RTT, and a 10 Gbps throughput?
This inquiry pertains to the distinction between TCP's full-duplex service and connection-oriented service?
Previously somebody did it wrong , so leave it if you are not good in it. This time i will report and downvote . Try ony if you are 100% sure.
Using TCP EWMA, calculate the timeout value for the 10th TCP transmission. Assume the following: The initial instantaneous and average RTTs are 500 ms each. It is observed that the instantaneous RTT increases by 10 ms each transmission round.