5-126* A short standard-weight steel pipe (see Appendix B) is used to support an axial compressive load of 100 kN. If yield- ing (o, = 250 MPa) should not occur and the factor of safety is to be 1.6, determine the smallest nominal diameter pipe that may be used to support the load.

5-126* A short standard-weight steel pipe (see Appendix B) is used to support an axial compressive load of 100 kN. If yield- ing (o, = 250 MPa) should not occur and the factor of safety is to be 1.6, determine the smallest nominal diameter pipe that may be used to support the load.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The one end of a hollow square bar whose side is 10.35 in with 1.35 in thickness is under a tensile…

Q: The one end of a hollow square tube whose side is 10.47 in with 1.47 in thickness is under a tensile…

A: Cross section of the bar,Hollow square tube, a=10.47 inchthickness, t=1.47 inchtensile stress on…

Q: in the figure. Also, determine the factor of safety for the tank based on Von-Misses and Tresca…

Q: Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Mpa steel bronze A= 300mm2…

A: Given: The maximum allowable stress in steel rod = 120 MPa The maximum allowable stress in bronze…

Q: The lap joint is fastened with four 3/5 in-diameter rivets. The allowable normal stress in the…

A: To Find: The maximum safe axial load P. Given : The diameter is d=35 in. The normal stress is σ=30…

Q: - 62.5 mm - Key 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm…

Q: cast aluminum cylinder of a portable hydraulic riveter is d mm in diameter. The pressure of the…

Q: find the required wall thickness of the cylinder.

A: find the required wall thickness of the cylinder.

Q: Force on the Bronze Material Force on the Aluminum Material Force on the Steel Material Maximum…

A: To find. Force on the Bronze Material Force on the Aluminum Material Force on the Steel Material…

Q: The compression load of 120 kN acts on the steel pipe of Table B-14. Determine the minimum Nominal…

A: Compressive load =120kN Factor of safety =1.5 Yield strength =240 MPa Let diameter be "d"

Q: Q3/ Decide if the copper wire made of ( 4 mm) in diameter is fail or not when it used for pulling a…

Q: The one end of a hollow square bar whose side is (10.50) in with (1.50) in thickness is under a…

A: Given data: The side of the square bar is a=10.5 in The thickness of the bar is t=1.5 in The tensile…

Q: The one end of a hollow square bar whose side is 10.68 in with 1.68 in thickness is under a tensile…

Q: The thin-walled pipe has an inner diameter of 4 in. and a wall thickness of 0.1 in. If it is…

Q: A pressure of 40 MPa shall be contained in a pressure vessel with inner diameter 0.30 m. Find the…

A: Given: Pressure, P = 40 Mpa Inner diameter, d = 0.3 m Maximum tensile stress, σu = 646 Mpa Factor of…

Q: Jason took a steel rod, 15.29-mm in diameter, and held snugly (but without any initial stress)…

A: Given: The diameter of rod, D = 15.29 mm The coefficient of thermal expansion, α = 13.6x10-6 mm/mmoC…

Q: Q-5 Wall thickness of a thin cylinder shell of 800 mm internal diameter is 10 mm. length of the…

A: internal diameter of cylinder(d)=800 mm=0.8mwall thickness(t)=10m=0.01minternal pressure…

Q: Problem 8-21: If the load has a weight of 600 lb, determine the maximum normal stress on the cross…

Q: The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness…

A: Data given- N= 47 So Side of sqaure x = 10+ 47/100 = 10.47 in Thickness t = 1+47/100 = 1.47 in…

Q: The structure below is made from stock (same stock for A-B-C and B-D) that is 5 mm thick (into the…

Q: A cylindrical hollow tube with closed ends is pressurized to a gauge pressure of 10 MPa and twisted…

Q: PROBLEM F8-13 A 100 mm long rod has a diameter of 15 mm. If an axial tensile load of 10 kN is…

Q: Determine the state of stress at point A on the cross section of the pipe at section a - a. Take P=…

A: Data given P = 6.1 kN ro = 50 mm ri = 40 mm

Q: The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: given from the above diagram,From the FBD of joint B, we get

Q: 6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 1D…

A: force, F=σ×AF=3.5×π4×4302F=508270.42 NP=F

Q: A steel boiler 2.5 m in diameter has a wall thickness of 25 mm. The internal pressure is 1.6 MPa.…

A: Given: d=2.5 m t=25 mm P=1.6 MPa S=250 MPa

Q: Determine the bolt stress for an internal pressure of 500 psi.

A: Given dataequally spaced steel bolt the diameter of the bolt the pre-load of each bolt the number…

Q: Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load P at…

Q: The one end of a hollow square bar whose side is 10.69 in with 1.69 in thickness is under a tensile…

Q: Electrical strain gauges were applied to a notched specimen to determine the stresses in the notch.…

A: Given:Strain along the x-axis, εx=0.0019Strain along the y-axis, εy=-0.00072

Q: Problem 8-5: Air pressure in the cylinder is increased by exerting forces P = 2 kN on the two…

Q: Find bearing stress in the Revit connection of 15 mm diameter, if the applied load (P= 15 kN), the…

A: Given Revit diameter =15mm Applied force =15kn Thickness of plate= 20 mm We have to determine the…

Q: A 3 m long hollow circular tube made from aluminium with an outside diameter 200 mm and a wall…

Q: Ferd plate Q3// Figure.3 show the arrangement of a support bracket where the detachable plate is…

A: Given:Load,W=40 KNYield stress, Syt=160 N/mm2number of bolts,n=6bolt diameter,d=20…

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter of this chip…

A: Draw the free-body diagram of the system as shown below, Taking moment about C,…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

Q: The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly…

A: List down the given data.The outer diameter of copper is The inner diameter of copper is The torque…

Q: The lever is attached to the shaft A using a key that has a width d and length of 26 mm If the shaft…

A: Given F = 200 N Width = d Length (L) = 26 mm Shear stress = 37 MPa

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A: Loads acting on a body induces stresses in all directions at any point of the body. The point can be…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

100%

5-126* A short standard-weight steel pipe (see Appendix B) is
used to support an axial compressive load of 100 kN. If yield-
ing (o, = 250 MPa) should not occur and the factor of safety
is to be 1.6, determine the smallest nominal diameter pipe that
may be used to support the load.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Show complete solution pls A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. Thechanges in dimension caused by an increase in temperature of 80°C for the:1. Outside diameter 2. Inside diameter 3. LengthNote: All answer must be round off up to 3 decimal places.
To determine the magnitude of the velocity and acceleration of the follower rod AB at this instant. The surface of the cam has a shape of a limacon defined by r = (200 + 100 cosθ) mm. Express your answer to three significant figures and include the appropriate units. only HANDWRITTEN answer needed ( NOT TYPED)
X=7,Y=8 Give me right solution according to the question
O d. NA = 0.374 , Ng = 2.611 Clear my choice The pipe assembly shown is subjected to a force F = 12 kN and P = 6 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. 1.2 m 0.65 m d= 176 mnm D- 200 mm Cross section Select one: O a. NH =4.07 360=5355 Od.N-8576 solid rounc bar deep wich a 2 5-mm radiu 1:14 AM fla )) ENG 22/4/2021
Asap within 20 mins will voteup
Three cables having an area of 0.05 in^2 each is carrying the load W as shown. With no stress, the original lengths of the cables are 74.99 ft, 75.00 ft, and 74.94 ft. E = 29 x 10° psi Calculate for the stress in the intermediate wire. Choices: a. 8,026.65 psi b. 9,999.66 psi c. 19,939.80 psi d. 10,102.52 psi 1500 lb
PLEASE ANSWER ASAPMN= 76 ksiSN= 50 ksi
5 Please help. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
5.5 Please help. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
Given Value:D1 = 250 mmD2 = 160 mmP = 3.5
The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile stress and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σallowable=243 ksi for pin material.