Answered: 4/66 For an 80-N squeeze on the handles…

4/66 For an 80-N squeeze on the handles of the pliers, determine the force F applied to the round rod by each jaw. In addition, calculate the force supported by the pin at A. 80 N 35 mm 95 mm A 80 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Related questions

Q: answer is 900.8 please resolve

A: Given Data

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: Solve the triangle AABC a = 10ft , %3D A = 35°, B = 25° %3D Angle C = type your answer... degrees,…

A: Given : The length of side a = 10 ft Solution: The sum of the angles of a triangle is 180° Thus ,…

Q: Q6 Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke…

Concept explainers

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.

Question

Show complete solution. Draw FBD

4/66 For an 80-N squeeze on the handles of the pliers,
determine the force F applied to the round rod by
each jaw. In addition, calculate the force supported
by the pin at A.
80 N
35 mm
95 mm
A
80 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Take a "cut" at H (draw a proper FBD) and determine the forces at H.
Determine the force supported by the pin at A for an 80-N squeeze on the handles of the pliers. (Hint: Draw free body diagram of each handle) -35 mm- 95 mm- 80 N 80 N
The bracket is held to the wall using three A-36 steel bolts at B, C, and D. Each bolt has a diameter of 0.5 in. and an unstretched length of 2 in. If a force of 800 lb is placed on the bracket as shown, determine how far, s, the top bracket at bolt D moves away from the wall. For the calculation, assume that the bolts carry no shear; rather, the vertical force of 800 lb is supported by the toe at A. Also, assume that the wall and bracket are rigid. A greatly exaggerated deformation of the bolts is shown.
Identify the zero force members (if any) in the trus P 4 m -3m
For a given gripping force P, determine the normal force Q exerted on the small round stock by each jaw of the compound pliers. 4.1" 1" 2.7"- 6.9"
Q-4. Determine the "Horizontal Displacement" of Joint "A of the below given frame by using the "Method of Virtual Forces". 6 ft B 200 lb -6 ft- 8 ft
The needle-nose pliers are used to either cut objects at location A or grip objects at location B. Compute (a) the cutting force at A and (b) the gripping force at B in terms of the applied force F. Determine the magnitude of the pin reaction at O in both cases. Neglect the effects of the slight opening of the jaws to accommodate the gripped items.
Also determine the magnitude of the force at O. Express your answer in units of N.
1) Determine the force acting on the hydraulic cylinder BC. Express your answer in pounds to three significant figures. 2) Determine the horizontal and vertical components of reaction at the pin A(Ax,Ay). Express your answers in pounds to three significant figures separated by a comma.
Prob 6-43 12 kN 6kN G 9 kN 4kN H B 1 m 2 m 1 m 1.5 m 1.5 m C D 1.5 m -15 m 6kN In this problem, you are asked to determine the forces in members CD, CJ, GJ, and CG. Now solve the problem using the method of sections.
The electric power transmission tower supports two wires that apply 18 kN vertical forces, and the 36 kN horizontal force crudely models wind loading during a storm. Use the method of sections to determine the force in members IF, IM and BD. -2.4 m-- 6 m -2.4 m- M 1.2 m TH 18 kN 3.7 m 18 kN 36 kN G 3.7 m C D 3.7 m 1.5 m 1.5 m B.
The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces are applied to the handgrips. (Hint: The horizontal components of pin forces at B and D are zero due to symmetry.)