4/61 The depicted structure is under consideration as the upper portion of a transmission-line tower and is supported at points F, G, H, and I. Point C is directly above the center of rectangle FGHI. Determine the force in member CD. 2a CD=2.4L

Q: The 50-lb rectangular access door is held in the 90° open position by the single prop CD. Determine…

A: Given the weight of door and the position of door.  Required: F, A and B

Q: The light right-angle boom which supports the 260-kg cylinder is supported by three cables and a…

A: The mass of cylinder is m=260 kg

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: a=(3.7m) , b=(3.7m) ,theta =(33) , p1=(3.7)KN , p2=(2.4)KN     find the forces in each members…

A: According to the given dataWe need to findforce in each member.

Q: Problem 3: If the springs shown each have an unstretched length of 48 inches, determine the angle…

A:

Q: Figure 1 shows a door of size 1200 mm by 400 mm supported by hinges at an inclined axis. E is at the…

A:

Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…

A:

Q: The rectangular plate of sides 560 mm x 1590 mm is supported by hinges along its side BC and by the…

A:

Q: The system shown is supported by cables BC and BD, as well as a ball-and-socket joint at point A.…

A:

Q: Use the method of MEMBERS to determine the true magnitude and direction of the forces in members1…

A: Force F = —1500 lb

Q: m The hoist supports an engine Determine magnitude of the force created by the engine mass

A: tanθ1=a+ba-btanθ1=2.2+1.12.2-1.1θ1=71.56o∑Fv=0RA+RB-mg=0RA+RB=mgRA+RB=175×9.81RA+RB=1716.75 N ,…

Q: 3. The screw eye is subjected to two forces, Fr and F2. Resolve the force F1 into its vertical and…

A: Calculated vertical and horizontal component of force F1.

Q: The 46-lb rectangular access door is held in the 90° open position by the single prop CD. Determine…

A: The weihght of rectangular plate is .

Q: The 50-lb rectangular access door is held in the 90° open position by the single prop CD. Determine…

A: Here G represents the center of gravity Following data is provided Weight of the door W=50 lb a=26…

Q: #4 Handle AC can only rotate about the z-axis at point A. A 10 lb force is applied as shown at point…

A:

Q: If the element shown is equilibrium F1-552 N, F2-381 N, a-30, B-43", a-0.32 m, b-0.19 m, and c-0.19…

A:

Q: consider the rotational axis at the point where the tire contacts the ground, directed perpendicular…

A: A man is pulling a wheelbarrow to lift the weight. A wheelbarrow is a vehicle to lift weight…

Q: The h = 110 ft tall communication tower is supported by three cables at A and a ball-and-socket…

A: To Find : The magnitude of the tension in cable AD,AB  and AO. Given :  The height of tower is…

Q: A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B,…

A:

Q: The hanging structure in the figure below is homogeneous. Its weight (40 kg) is acting at the center…

A:

Q: Complete solution required with free body diagram. Handwritten format recommended

A:

Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…

A:

Q: Problem 3. Determine the vertical clamping force at E in terms of the force F applied at the handle.…

A:

Q: The bent rod is supported at A, B, and C by smooth journal bearings as shown in. The rod is…

A: