The ramp is used as passengers board a small commuter airplane. The total mass of the ramp and six passengers is 715 kg with a mass center at G. Determine the force in the hydraulic cylinder AB (positive if in tension, negative if in compression) and the magnitude of the pin reaction at C. 740 mm 610 mm 1250 mm 2375 mm Answers: AB = i N C = i N

The ramp is used as passengers board a small commuter airplane. The total mass of the ramp and six passengers is 715 kg with a mass center at G. Determine the force in the hydraulic cylinder AB (positive if in tension, negative if in compression) and the magnitude of the pin reaction at C. 740 mm 610 mm 1250 mm 2375 mm Answers: AB = i N C = i N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.26P: The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A...

See similar textbooks

Related questions

Q: The figure shows the cross section of a circular steel tube that is filled with concrete and topped…

Q: can u pls solve the question using hand written notes in detail and figure

Q: Find the area of the figure shown. a=3 cm b= 6 cm Take pie3D3.14 Round answer to one decimal place.…

A: It is required to determine area of given section

Q: Finish the Orthographic drawing

A: Please refer the following Front view, right hand side view and top of the given isometric view. 1…

Q: Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke length…

A: Given Data Diameter of cylinder is :d=60 mm Stroke length is :L=400 mm No of cylinders is :N=6 Now…

Q: Please do the last three questions (2, 3 and 4)! Thank you in advance! A seesaw that weights 45lbs…

A: The problem is based upon the moments and principal of moments. The dimensions in meters will be…

Concept explainers

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.

Question

100%

Need a answer to 3 decimal points

The ramp is used as passengers board a small commuter airplane. The total mass of the ramp and six passengers is 715 kg with a mass
center at G. Determine the force in the hydraulic cylinder AB (positive if in tension, negative if in compression) and the magnitude of
the pin reaction at C.
G
740 mm
610 mm 1250 mm 2375 mm
Answers:
AB =
i
C =
i
N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Need help drawing the FBD as well.
For the frame shown, determine the magnitude if the pin reaction at B. Neglect the weight of the frame.
Please write solution to be legible and clear. Thanks
The system shown consists of three cables; 1, 2 and 3. Cable 1 passes through a frictionless pulley. A 6 kg mass is suspended. Determine the force in cable 3 considering the following data: y1 = 1.3 m, y2 = 1.1 m, y3 = 1.8 m, and x1 = 2.7 m.
Please see attached
The weight of the limb is W=15 lbs.The contact of foot with the ground can be modeled as a pin/hinge here. Determine the reaction force of the ground and the reaction at the knee joint and its direction/angle θ. Note: use the thee force member condition to find the angle of FK.
2. The backhoe supports a 7.5 kN weight of soil in the bucket which has a center of gravity at G. Find: 0.64 m 0.25 m ● 0.26 m 0.3 m 1.68 m Force in cylinder ED (indicate if force is in tension or compression) Force in cylinder FI (indicate if force is in tension or compression) OF 0.4 m 0.1 m A -1.44 m- 17.5 kN 0.25 m D B m E 0.22 m 0.45m H O SUSIS Force in ED = Force in FI = KN (Tor C) kN (Tor C)
the tree feller cuts off large trees near ground level and then continues to grasp the trunk. Determine the force in hydraulic cylinder AB for the position shown if the tree weighs 6000lb. Determine the required pressure on the 4.72-in.-diameter piston of the cylinder. draw the free body diagram
The machine shown is used to help load luggage into airliners. The combined mass of the conveyor and luggage is 110 kg with mass center at G. Determine and plot the force in the hydruaulic cylinder BC (report your answer as a positive value) as a function of over the range 5° 0 ≤ 36°, then answer the questions. Assume DE = 2070 mm, CD = 1280 mm, c = 1680 mm, d = 1130 mm, e = 570 mm, f = 2380 mm. t Questions: E B i D If 0 = 11°, BC = If 0 = 21°, BC = i Over this range, the maximum value for BC = i N N N and occurs when 8 =
The mass center G of the 1400-kg rear-engine car is located as shown in the figure. Determine the normal forced under each tire when the car is equilibrium. State as assumptions. (CLO-3) of 1 1386 mm 964 mm
2. A machine operator produces the tension Tin the control rod by applying the force Pto the foot pedal. Determine the largest P if the magnitude of the pin reaction at B is limited to 1.8 kN. Neglect the mass of the mechanism. wwww wwwww 50 B 25° 150 50 T Dimensions in mm
The shear leg derrick is used to haul the 162-kg net of fish onto the dock. Determine the compressive force along leg AB. Assume the force in each leg acts along its axis. Supply the answer in kN and as a negative number. Add your answer 4 Additional content You can add text, images, and files here. PELL 5.6 m 4 m R