46.5 kg of fine aggregate is mixed with 72.3 kg of coarse aggregate. The fine aggregate has a moisture content of 2.0% and its absorption is 3.4% whereas the coarse aggregate has a moisture content of 1.3% and its absorption is 3.0%. Determine the amount of water required to increase the moisture content so that there is 1% free moisture in the aggregate blend.

Q: Well graded aggregate means sizes within the entire range are in approximately equal amounts,…

A:

Q: civil engg material

A: Gradation of Aggregate- It is defined as a process that helps in particle size distribution which is…

Q: Design a concrete mix for use in plain cement concreté (PCC) from the following data :…

A:

Q: Based on the data in Table P9.32, determine the design binder content for aSuperpave mix design for…

A: Pavement design: In-pavement there two types of pavements are there, one is Rigid pavement and the…

Q: Design a concrete mix to implement a concrete slab (exposed to sever conditions moisture and…

A: Given, f'c = 30 MPa S = 4 MPa  FM = 2.4  Apparent density = 1500 kg/m3

Q: A specific gravity test was performed on a sample of fine aggregate and produced the following…

A: To find Specific gravity of fine aggregates Classify aggregate on basis of surface texture

Q: Absorption of coarse aggregate 1.8% Moisture content in coarse aggregate 2.3% Dry weight of fine…

A: Amount of water contributed by coarse =MC-ABS×WTWC=0.023-0.018×1500=7.5lb

Q: Based on the data shown in Table select the blend for a Superpave design aggregate structure. Assume…

A:

Q: It is given that an aggregate mix has 260 grams of coarse aggregates and 240 grams of fine…

A: Given-260 gm of coarse aggregates, G=2.6240 gm of fine aggregates, G=2.4Bulk specific gravity of…

Q: 1)Determine the uncorrected and corrected weights based on the following data using the traditional…

A: Following is required mix design procedure :

Q: Q-If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60…

A: given- Given aggregate completely passes through 75 mm size sieve & retained on 60 mm size…

Q: Given the data in Table , select the blend and the design binder content for a Superpave design…

A:

Q: In an aggregate mix, the proportions of coarse aggregate, fine aggregate and mineral filler are 55%,…

A:

Q: A sample of wet aggregate weighed 297.2 N. After drying in an oven, this sample weighed 281.5 N. The…

A:

Q: The bulk unit weight of the dry-rodded aggregate inside a rigid container is 25 kN/m3. 35 percent of…

A:

Q: A sample of coarse aggregate was tested in a laboratory to find its moisture content. The wet weight…

A: Dry weight=5235.1gmWet weight=5403.5gmMoisture content=Wwet-WdryWdry×100Free water=MC-Absorption

Q: Three types of aggregate have sieve analysis as given below. Combine these types of aggregate to…

A: Sieve, inches3/41/23/8No.4No.8No.30No. 50No. 100No.…

Q: In an aggregate mix, the proportions of coarse aggregate, fine aggregate and mineral filler are 55%,…

A:

Q: 5) A 2000 g coarse aggregate sample in SSD condition weighed 1272 g when immersed in water. The same…

A: Specific gravity is a dimensionless unit defined as the ratio of the density of a substance to the…

Q: 1000 g coarse aggregate sample taken from the site showed the following properties in the…

A: Bulk Dry specific gravity is given by ;Bulk Dry specific gravity = Bulk Dry specific gravity = Bulk…

Q: It is given that an aggregate mix has 260 grams of coarse aggregates and 240 grams of fine…

A:

Q: The percentage of aggregates of fine-ness modulus 2.7 is to be mixed with coarse aggregate of…

A: Given data: The percentage of aggregates of fine-ness modulus (FM) = 2.7 be x It is to be mixed with…

Q: Problem 3 (30 points): A sample of the aggregate and compacted HMA are known to have the following…

A: The given values: Effective specific gravity, Gse=2.726 Specific gravity of Binder, Gb=1.030 Bulk…

Q: Coarse aggregate is placed in a rigid bucket and rodded with tamping rod. The volume of the bucket…

A: Given data: Volume of bucket=20,000 cm3. Weight of aggregate= 400N. Bulk specific gravity of the…

Q: : What is meant by: 1. absorption, 2. Moisture content (MC), 3. Bulk density of aggregate,

A: 1. Adsorption-  It is surface phenomena, It is the adhesion of atoms, molecules or ions from a…

Q: In proportioning a concrete mix, the coarse and fine aggregates had the following properties…

A: Coarse aggregate weight = 800 lbDry aggregate weight = 350 lb

Q: e mix design

A: Step 1: Calculation of target mean strength ft=fck+1.65α where, α is the standard deviation here,…

Q: Coarse aggregate is placed in a rigid bucket and rodded with tamping rod. The volume of the bucket…

A:

Q: Design a concrete mix to implement a concrete slab (exposed to sever conditions moisture and…

A: Given, f'c = 30 MPa  S = 4 MPa  FM = 2.4

Q: The wet mass of an aggregate sample is 583g and its dry mass is 575g. The test shows the absorption…

A: Finding out the type of moisture condition.

Q: A concrete mix required for construction of an industrial building. Cement is PKC32,5. Specific…

A: Taking the volume of trial mix be 1 cubic meter : According to ACI code slump required for…

Q: what is the requirement volume of fine aggregates (s.g. = 2..4) if the mass nedded for the concrete…

A:

Q: Design a concrete mix according to the following conditions:   Design Specifications  Concrete…

A: All the design calculations and specifications are based on ASCE codes.   For 50mm slump and 37.5mm…

Q: Q1/ If the weight of Cement is 3000 g and the mix proportion is 1:4:8 Calculate the following: 1)…

A:

Q: A civil engineer wants to design a concrete mix design with the following criteria: Design a…

A: Concrete Mix Design: Blend configuration can be considered the most common way of choosing…

Q: Fine aggregate sample was tested to find its physical properties. The test results were as follows:…

A: Solution: Given Data: Bulk specific gravity=2.42 Apparent specific gravity=2.58 Mass of vessel full…

Q: Question 6 f in a concrete mix, the fineness modulus of coarse aggregate is 7.6, the fineness…

A: From Given Data : For given concrete mix: Fineness modulus of coarse aggregate = (FM)CA = 7.6…

Q: 6. A sample of lightweight coarse aggregate weighs 532.3 g when oven-dried, 615.7 g when saturated…

A:

Q: For a design a concrete which will be exposed to seawater and sulfates in a structure that comprises…

A: Mix design is the selection and designing of proportion of ingredients needed for producing a…

Q: The following table provides data obtained during a specific gravity and absorption test on coarse…

A: The mass of oven-dry sample in the air (g), A = 2998.4The mass of the SSD sample in the air (g), B =…

Q: The moisture content of an aggregate is equal to the ratio between the original weight of the sample…

A: