- once answered correctly will UPVOTE!! The flywheel rotates with an angular velocity of w = (40/2) rad/s, where 0 is in radians.(Figure 1)Part ADetermine the time it takes to achieve an angular velocity of w = 176 rad/s . When t = 0, 0 = 1 rad.Express your answer to three slgnlficant flgures and Include the approprlate units.?t =ValueUnits

Answered: Image /qna-images/answer/09d7bd0c-30c6-4c2e-9f1d-b44633ea8b04.jpg

Answered: (40'/2) rad/s, where 0 is in radians.…

Engineering

Mechanical Engineering

(40'/2) rad/s, where 0 is in radians. The flywheel rotates with an (Figure 1) angular velocity of w =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer in 4-10
Please help
In the following milling method, metal is cut by a cutter rotating in the same feed direction Select one: O a. Metal is not removed O b. Inclined milling O c. Up milling O d. Down milling
What is the process of locating the instantaneous center?
- For the slider – crank mechanism illustrated in Fig.2 A) Determine all instant centers.
Solve first Question Only.
Find the end mill diameter for slotting operation by a cutting speed of 18 meter /minute and spindle speed of 260 rpm. End mill diameter in mm =
Industry Print Exercise 23-2 Refer to print PR 23-2. The sequence of operations for this print is given below. Answer the questions following the sequence of operations. Sequence of Operations descends at a controlled rate, slowly compacting the explosive charge to avoid detonation due to a sudden Description: This is a system to control a 90-ton hydraulic, explosive-compaction press. The press ram shock. 1. The cycle is started by energizing solenoid A, which shifts control valve 3 and supplies pressure to the head end of the hydraulic cylinder (7). This operates the ram. 2. The cylinder (7) extends at a slow rate controlled by the fluid in the rod end of the cylinder, which is vented through the flow control valve (5). the 1. When de-energizes solenoid A and energizes solenoid B. This shifts control valve 3 to retract the cylinder (7). de rol valve 5 has an integral check valve that permits the free flow of fluid in the opposite direction, causing the cylinder (7) to rapidly retra…
Where is the instantaneous center of rotation of bar BC?
Question 1 Figure Qta shows two cables attached to a half-ring anchor point as shown in Figure Q1a. Force Fi acts vertically with a force of 2170 N; and F2 acts at an angle e relative to the y-axis with a force of 1240 N. F1 F2 Figure Qta Cable Anchor Point a) For Figure Q1a, at what angle @ must the force F2 ( 1240 N) be applied in order that the resultant force R of the two forces Fi and F2 has a magnitude of 3100 N? Give your answer in degrees to 2 decimal places. b) For Figure Q1a, what is the angle between the resultant force R (3100 N) and the yaxis. Give your answer in degrees to 2 decimal places. c) The pulley system shown in Figure Q1c lifts a mass, m, of 550 kg. Calculate the force Fanecessary to maintain the suspended mass in static equilibrium; and determine the forces at the ceilling anchor points A and B. Assume frictionless and weightless pulleys and useg-9.81 m/s'.
QUESTION 5 Determine the spindle speed (rpm), the feed rate (in/min) and the cutting power required for turning a 1º diameter copper rod with a depth of cut of 0.1" using a cemented carbide tool. O N=287 RPM, F-25.8 in/min, P=9.7 hp ON=2866 RPM, F=258 in/min, P=97 hp ON=1146 RPM, F-25.8 in/min, P=97 hp O N= 11460 RPM, F-340 in/min, P=130 hp ON= 1146 RPM, F-34 inimin, P= 13 hp ON= 115 RPM, F-3.4 in/min, P=1.3 hp QUESTION 6 It is required to face mill an aluminum block to size it down from 2" to 1.5" thick using a 3" diameter 2-toothed carbide cutting tool. The block is 6.0" wide and 6" long. The entire tool diameter engages the workpiece during the cut. Calculate the recommended spindle speed in revolutions per minute, feed per tooth, and cutting power required. O N=1529 RPM, f= 0.026 in/rev/tooth, P = 36 hp O N-3820 RPM, f= 26 in/revitooth, P=27 hp O N-3820 RPM, f= 0.052 in/rew/tooth, P=27 hp ON-382 RPM, F= 0.026 in/revitooth, P = 0.027 hp O N-3820 RPM, f= 0.052 in/rev/tooth, P=2.7 hp…
Machine ELEMENTS Assume w2 is clockwise answer P.11