40 kN 3m 1m A MATHalino.com Fiqure P-351

Q: One of the following is not used to reduce the setup time? a. Using power clamp b. Using softer raw…

A: The setup time can be reduced by - Eliminating waste Using power clamp Design for manufacturability…

Q: how did you find humidity ratio

A:

Q: Derive an espression for the height of propell governor

A: Deriving expression for proell governor considering proell governor taking moment about point…

Q: What improvements can be done to increase the efficiency to boil the water?

A:

Q: Procedure on how to make the head of a meat tenderizer.

A: The procedure to make the head of a meat tenderizer is as follows: Step 1: Cutting a pattern of a…

Q: Example of how to size a globe valv

A: A globe valve is a type of valve that has a moveable plug or disc element and a stationary ring…

Q: safety in general shown in picture

A: Let us discuss Safety in general,  which are generally used at industries and big industries.

Q: what is the minimum energy to do a 1kw power

A: Given: Power, P = 1 kW = 1000 W Energy, E = ?

Q: tarting friction is low in: A.   Hydrostatic lubrication B.   Hydrodynamic lubrication C.   Mixed…

A:

Q: Explain and give details about Run to failure strategy under plant maintenance

A: The Run to failure strategy is the simplest maintenance strategy. In this strategy assets are…

Q: What is the waterline

A: Solution:   The correct answer with necessary explanation is given below:

Q: Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20…

A:

Q: If a wind turbine is facing a wind velocity of 23.4 m/s, then it is Select one: a. Survival speed b.…

A: Solution: The maximum wind speed is also known as the maximum survival speed, is the speed above…

Q: List the two key determinants of pump selection.

A:

Q: Identify the point to be considered while maintenance of  wiper pads on lathe machine Regularly…

A:

Q: An example of a performance with two phases is the bench press; in the down phase the lifter lowers…

A: The preparation phase and the movement phase of the bench press exercise can be separated.…

Q: A low Reynolds number will result in a precipitate a. Bad sort b. Good sorting c. round c. Uncertain

A: A low Reynolds number will result in a precipitate  Good sorting.

Q: Decribe different types of jet from orifice.

A: Orifice: Orifice is a small opening of any cross cross sections such as circular , rectangular on…

Q: HOW TO PERFORM LEAK TEST ON HVAC DUCTS? Badly needed asap. Brief and clear Explanation. I will rate…

A: The leak test on HVAC ducts is performed in few steps. These steps are given as under,

Q: Please explain briefly on how filter with lower pressure drop can increase the eficiency of…

A: Filtration is the process of separation of bigger size particles from a fluid by passing through a…

Q: 1.Name type of failures in engine blocks

A: The engine is the most important part of the IC engine. In production, Every company produces an…

Q: What volume of oil to the cylinder is required to cause the cylinder to advance at a speed of 392…

A: Given Data: The speed of advance of the cylinder is, C=392 in/min. The diameter of the piston is,…

Q: Starting friction is low in: A.   Hydrostatic lubrication B.   Hydrodynamic lubrication C.   Mixed…

A: Given data To select the  correct option.

Q: . Describe clear flood mode and why it is used.

A: Given data : Clear flood mode

Q: Give any four significance of API Standard

A: American Petroleum Institute (API) Standard:-  American Petroleum Institute of standards Improve…

Q: Instruction: Explain why is it impOrtant t0 calibrate the pressure gauge.

A:

Q: es several activities divided into three groups and these

A: The average time required to troubleshoot and repair failed equipment is measured by the mean time…

Q: Write down the name of Primary Control Surface

A: The rudder is a fundamental control surface which is typically controlled by pedals rather than…

Q: Consider the 2D surfaces submerged in a stationary body of water, where the location of the…

A: Option (b) is correct option.

Q: Technician A says that coolant hoses should be squeezed to check for hardening or softening.…

A: Solidly squeeze both the upper radiator and radiator hoses. They ought to feel firm, solid, and…

Q: List no less than 4 kinds of modem advanced drilling rigs and analyze their characteristics.

A: The objective is to list 4 types of drilling rigs and write down their characteristics

Q: What do you mean by intake stroke?

A: Intake stroke: It occurs when suction occurs due to downward movement of piston in an internal…

Q: Gate AB in Figure is 4 ft wide into the paper, 6 ft long, and has weight W= 800 lb. It is hinged at…

A: The FBD of the diagram is shown below - a) The force of water on gate AB is  - FP = ρgAxFP =…

Q: or safety of plant which department is responsible?

A: Given Data⇒ Department Safety of plant

Q: Reflector is used in solar dryer. Select one: True False

A: We are to determine if reflector is used in solar dryer

Q: Please draw/show a picture of atleast 15 PIPE FITTINGS that you know.

A: Here are the pictures of pipe fittings that we know. These pipe fittings are given as under,

Q: The optimum effective temperature for human comfort is ?

A: For a human being,

Q: Compressed air can be used to clean the machine, is a general safety precaution while working in a…

A: It is important to follow the safety guidelines while working in a workshop. They are provided in…

Q: Which one of the following statement is correct for steam nozzle? O a. Outlet velocity of the steam…

A: Let us first understand how steam nozzle works: Steam nozzles are generally used in power plants…

Q: Briefly explain what a pH probe is and how it works

A: A pH scale represents the acidic or alkaline nature of a substance. It is between 0 and 14 , where…

Q: SLPM stands for _______ liters per minute a. speed b. standard c. static d. specific

A: SLPM is a unit of measuring volumetric flow rate of a gas.

Q: Alm that He Cafle

A:

Q: If atmospheric presure and tempreture whas not given how would you determine it

A: If the atmospheric pressure and temperature were not provided, we could determine approximate values…

Q: The friction work is Select one: O a. The difference between the indicated work and the pumping…

A: The friction work is defined as the difference between the indicated work and the pumping work.

Q: which type of furnace is used for installation in a crawl space?

A: To explain: The type of furnace is used for installation in a crawl space.  Concept used: Crawl…

Q: What is stand for AFUE and explain its efficiency system

A: AFUE stands for Annual Fuel Utilization Efficiency.

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.