4.91 Determine the clamping force at A due to the 75-N horizontal force applied to the handle at E.

Q: Determine approximately, the reactions at A, B, C, and D. Use portal frame method.

A:

Q: If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the…

A:

Q: P. 4m C 4m D 4mE 4mF 4m G 4 mHAnh I Amtm. 32m

A: Truss is an axial force member structure means truss always resist the force by means of axial or…

Q: Choose the magnitude (kN) and type (tension or compression) of the force in member AC.

A: To determine the force in member AC of the given truss.   The force in member AC can be obtained by…

Q: eta = 30 degree T = 6kN   Find the magnitude of the resultant forces acting on the eyebolt.

A: Rx=Tsinθ+8cos45Ry=Tcosθ-8sin45Rx=6sin(30)+8cos45Ry=6cos(30)-8sin45Rx=8.65685kNRy=-0.4607

Q: Referring to Figure Q1(a) until Figure Q1(e); (i) Check the stability and the determinacy of the…

A: "Since you have asked multiple question we will solve the first (B) for you. For other questions to…

Q: Properties of the Wide Flange Section: gy tf = 61 mm bf d = 1,050 mm Iax = 14.734 x10° mm4 Iay =…

A:

Q: 4) Find the magnitude and direction of the resultant force and moment at A 1414.21lb 2.53' -1000lb…

A: To find resultant and moment about point A

Q: Draw the Axial force digram and shear force and bending moment

A: Given:Required:Axial force,shear force and bending moment diagram

Q: At maximum shear location along the beam, find the shear stress deue loped in points B and C shown…

A: Draw the free body diagram.

Q: From the given truss shown compute the force in member ED FD, and FC

A: Step 1: Step 2:

Q: in Figure A truss is supported by a pin at A and a cable attached at Q2(b). Determine the reactions…

A: To find the support reaction at A and force ni cable -

Q: 02/ The truss gusset plate is subjected to the forces of three members. Determine the tension force…

A: To find Tension force in member C

Q: Determine the force in member BE of the loaded truss

A: Compute the length:Using the sine rule:

Q: Far the cantilever shown. X 6m Determine the internal shear force at distance 4m to the nght of…

A: Introduction : Shear force : Internal shear force is the adding of forces from right to section or…

Q: Point A is a slotted connection that allows free vertical movement along the upper portion of member…

A: ##Determination of horizontal and vertical components of reaction forces##

Q: P Determine angle a at which force P should be applied (see figure above) such that the shear centre…

A: Given, Shear centre deflects at 60° with the vertical y.

Q: 242. Determine the horizontal and vertical components f reaction at A, C. and D. Asume the frame is…

A:

Q: drs - The semicircular rod has a 200 N load acting on it at the lower end in the direction shown in…

A: Given Data: The load acting on the lower end of the rod is P=200 N. The radius of the semicircular…

Q: E=200 x 10° N/m? A=300mm2 L=3m B. 3 m 4.5 m P.

A:

Q: Draw the shear force digram and bending moment digram

A: Given data in question UDL 20kN/mPoint load 40 kNSpan 6 mTo find out SFDBMD

Q: Prob. 4-6: The simply supported truss shown is 1.80 meters at king post. d. 182.73 b. 204.70 b.…

A:

Q: Determine the resultant force at pins A, B, and C on the three-member frame.

A: Calculating slant height and base of the loading diagram:

Q: 100 N 800 N-m •B 5 m 5 m

A:

Q: 2m 1.5m C 1.5m E 1.5m 388N

A:

Q: ES S 2-34. Determine the horizontal and vertical components of force at the connections A, B, and C.…

A: Determine the horizontal and vertical component of the reaction at A, B and C.

Q: 2-43. Determine the horizontal and vertical components at A, B, and C. Assume the frame is pin…

A:

Q: 1. Determine the resultant internal loadings acting on the cross section at B of the pipe shown. End…

A:

Q: (21 - 24 ) Evaluate the given Fink Truss using method of sections. Answer the following questions if…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: 5-78. The bent rod is supported at A, B, and C by smooth journal bearings. Compute the x, y, z…

A: Introduction- A reaction force opposes an action force by acting in the opposite direction. During…

Q: 10 kip E | D 000 4 ft 7 kip F 000 000 4 ft A В 000 Which of the following is closest to the…

A:

Q: Determine the x-y and n-t components of the 18-kip force Facting on the simply-supported beam.

A:

Q: Find the stresses in the wires P1, P2, P3 shown if their diameters are 100mm  each and P3=20kN and…

A: Given data: R=40 Kn P3=20 Kn   It is asked to calculate forces P1 and P2

Q: Cover ABCD for an opening in the roof is hinged at corners A and B. The roof makes a 30° angle with…

A: solution Draw the free Body Diagram

Q: where should the cut section be if you need to find the force in member DE,BC and DC 3m B m 2m 10 KN…

A:

Q: Determine the horizontal and vertical components of force at pins A and D. 2m A -1.5 m -1.5 m- 0.3 m…

A: Given data : Structure is given with pulley at E of radius 0.3m Find : Reactions at A and D  Free…

Q: -200 mm E C 40 N 40 N 100 mm 90 N 90 N -100 mm---100 mm--100 mm- 16. Determine force-couple system…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: t Find the bar force in the active tension diagonal in the third panel from the left and the bar…

A: Given : Forces in members CD, JK, DK and CJ Active tension diagonal member is DK. We will use method…

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.